Owners manual

* FREE K&N
®
decal To register your warranty, please see us online at knlters.com/register. FREE K&N
®
decal *
INSTALLATION INSTRUCTIONS
Continued
ROAD TESTING:
37. It will be necessary for all K&N
®
high ow intake
systems to be checked periodically for realignment,
clearance and tightening of all connections.
Failure to follow the above instructions or proper
maintenance may void warranty.
35. Reconnect the vehicle’s negative battery cable.
Double check to make sure everything is tight and
properly positioned before starting the vehicle.
• 1455 CITRUS ST., P.O. BOX 1329, RIVERSIDE, CA., U.S.A. 92502 • TECH SERVICE 800-858-3333 • FAX 951-826-4001
• e-mail: tech@knlters.com
®
• WWW: http://www.knlters.com
®
1. Start the engine with the transmission in neutral
or park, and the parking brake engaged. Listen for
air leaks or odd noises. For air leaks secure hoses
and connections. For odd noises, find cause and
repair before proceeding. This kit will function
identically to the factory system except for being
louder and much more responsive.
2. Test drive the vehicle. Listen for odd noises or
rattles and x as necessary.
3. If road test is ne, you can now enjoy the added
power and performance from your kit.
4. K&N Engineering, Inc., requires cleaning the
intake system’s air lter element every 100,000
miles. When used in dusty or off-road
environments, our lters will require cleaning more
often. We recommend that you visually inspect
your lter once every 25,000 miles to determine
if the screen is still visible. When the screen is no
longer visible some place on the lter element, it is
time to clean it. To clean and re-oil, purchase our
lter Recharger
®
service kit, part number 99-5050
or 99-5000 and follow the easy instructions.
19632D
9/08/16
23. Install the 90° vent tting into the K&N
®
intake
tube as shown.
NOTE: Plastic NPT ttings are easy to cross
thread. Install the vent tting “hand” tight, then
turn it two complete turns with a wrench.
24. Install the straight vent tting into the K&N
®
intake tube as shown.
NOTE: On vehicles that are not equipped with a
vent line attached to the sound tube, install the
provided npt plug into the intake tube.
25.Install the hump hose (08418) onto the lter
adapter as shown using the provided hose clamp.
26. Install the step hose (08497) onto the K&N
®
intake tube as shown. Do not tighten the hose
clamp at this time.
27.Install the K&N
®
intake tube all the way into the
hump hose and then align with the throttle body.
Install the step hose onto the throttle body and
adjust the tube and hoses for best t. Then secure
the tube and hoses with the provided hose clamps.
28.Cut the provided breather hose as shown. The
short section should be 4.5” long; the long section
should be 11” long.
29. Install the provided hose menders into the cut
sections of breather hose as shown. The ½” hose
mender will go into the 11” breather hose. The ½”
to 5/8” hose mender will go in the 4.5” breather
hose.
NOTE: On vehicles that are not equipped with
the vent hose attached to the sound tube, the
½” hose mender and 11” breather hose will not
be used.
30. On vehicles equipped with a vent hose
attached to the sound tube, install the 11” breather
hose onto the tting in the intake tube and then
attach the hose mender into the EVAP breather
hose as shown.
31. Install the 4.5” breather hose onto the 90°
tting in the K&N
®
intake tube and then attach the
hose mender into the crank case breather hose as
shown.
32. Reconnect the air sensor electrical
connection.
33. Reinstall the fresh air intake scoop and secure
with the factory hardware.
34.Reinstall the engine cover.
36. The C.A.R.B. exemption sticker, (attached),
must be visible under the hood so that an
emissions inspector can see it when the vehicle
is required to be tested for emissions. California
requires testing every two years, other states may
vary.