Owners manual
69-5310TS
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery cable
erases pre-programmed electronic memories.
Write down all memory settings before
disconnecting the negative battery cable. Some
radios will require an anti-theft code to be
entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
®
HYUNDAI
2013 Genesis Coupe
V6-3.8L
TOOLS NEEDED:
Description Qty. Part # Description Qty. Part # Description Qty. Part #
A Hose Clamp #56 1 08620
B Hose; 4" ID to 3.5"ID X 3"L TPRD 1 08497
C Hose Clamp #64 Stainless 3 08645
D Vent; STRT 1/2" Hose, 1/4"NPT 1 080022
E Hose; 1/2"ID X 15-3/4"L 1 08414
F Hose Mender; 1/2" Barbed, Nylon 1 08686
G Bolt; M6 X 1.00 X 16MM 1 07730
H Washer; M6 Split Lock Zinc 4 1-3025
I Intake Tube 1 27334TS
J Hose Mender; 1/2" To 5/8" 1 08726
K Vent; 90DEG, 1/2"Hose, 1/4"NPT 1 08110FK
L Hose; 4"ID X 3"L Hump 1 08418
M Edge Trim (55") 1 102480
N Caplug; 1.5"OD X 1.0"L 1 081100
O Hose Clamp #20 Mini 1 08431
P Bolt;M6 X 1.00 X 12MM 1 07727
Q Bolt; M6 X 1.00" 12MM 2 07794
R Washer, 6MM Flat, SS 7 08269
S Bracket; 69-5310, STL, TB/PC 1 064304
T Stud; Rubber MNT, M/F, 1/2"L 1 070228
U Heat Shield 1 073138
V Bolt; 6MM-1.00 X 16MM, SS 2 07812
W Spacer, 0.937"OD X .437"ID 1 21715
X Bracket; 69-5310, STL, TB/PC 1 064305
Y Bolt; 8MM-1.25 X 20MM Hex 1 07787
Z Washer; M8 Split Lock Zinc 1 1-3036
AA Nut; 6MM Nylock, Hexhead, SS 2 07512
AB Adaptor; 57-3058 #454 1 27300
AC Hose Clamp #104 1 08697
AD Air Filter 1 RC-5138
AE Plug 1/4” NPT 1 08032
PARTS LIST:
Ratchet
Extension
13mm Socket
12mm Socket
10mm Socket
Flat Blade Screw Driver
Phillips Screw Driver
Pliers.
2. Lift up and remove the engine cover from the
engine.
3. Remove the four plastic screws that secure the
fresh air inlet scoop and then remove the scoop
from the vehicle.
4. Disconnect the electrical connection from the
inlet air sensor and unhook the wiring harness from
the air box.
5. Disconnect the EVAP hose from the factory
intake tube, and then loosen the hose clamps
securing the intake hose to the throttle body and
the engine sound tube to the inlet hose.
6. Remove the two bolts that secure air box to the
inner fender.
A
B
I
C
F
G
AE
H
E
C
C
P
U
AA
AB
AC
AD
N
O
H
S
T
Q
H
R
R
Q
H
R
M
L
D
J
E
K
R
R
Y
Z
V
X
W
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
If you need any assistance please call 1-800-858-3333 to speak with a representative
in our Customer Service Center before returning the product.