Owners manual

* FREE K&N
®
decal To register your warranty, please see us online at knlters.com/register. FREE K&N
®
decal *
INSTALLATION INSTRUCTIONS
Continued
1. Start the engine with the transmission in neutral
or park, and the parking brake engaged. Listen
for air leaks or odd noises. For air leaks secure
hoses and connections. For odd noises, find cause
and repair before proceeding. This kit will function
identically to the factory system except for being
louder and much more responsive.
2. Test drive the vehicle. Listen for odd noises or
rattles and x as necessary.
3. If road test is ne, you can now enjoy the added
power and performance from your kit.
4. K&N Engineering, Inc., requires cleaning the
intake system’s air lter element every 100,000
miles. When used in dusty or off-road environments,
our lters will require cleaning more
often. We recommend that you visually inspect your
lter once every 25,000 miles to determine if the
screen is still visible. When the screen is no longer
visible some place on the lter element, it is time
to clean it. To clean and re-oil, purchase our lter
Recharger
®
service kit, part number 99-5050 or 99-
5000 and follow the easy instructions.
ROAD TESTING:
33. It will be necessary for all K&N
®
high ow intake
systems to be checked periodically for realignment,
clearance and tightening of all connections.
Failure to follow the above instructions or proper
maintenance may void warranty.
31. Reconnect the vehicle’s negative battery cable.
Double check to make sure everything is tight and
properly positioned before starting the vehicle.
• 1455 CITRUS ST., P.O. BOX 1329, RIVERSIDE, CA., U.S.A. 92502 • TECH SERVICE 800-858-3333 • FAX [phone]
• e-mail: tech@knlters.com
®
• WWW: http://www.knlters.com
®
28. Install the K&N
®
air lter onto the lter adapter
and secure with the provided hose clamp.
NOTE: Drycharger
®
air lter wrap; part #
22-8049DK is available to purchase separately.
To learn more about Drycharger
®
lter wraps or
look up color availability please visit
http://www.knlters.com
®
.
29. Install the engine cover.
30. Install the fresh air duct and secure with the
factory retaining screws.
26. On vehicles equipped with an EVAP vent line,
Install the provided EVAP hose onto the purge
valve and then connect the other end to the vent
tting installed into the intake tube.
NOTE: Some trimming of the hose may be
necessary.
27. Install the provided crankcase vent hose onto
the valve cover port and then connect the other
end to the vent tting installed into the intake tube.
NOTE: Some trimming of the hose may be
necessary.
18952J
9/08/16
32. The C.A.R.B. exemption sticker, (attached),
must be visible under the hood so that an
emissions inspector can see it when the vehicle
is required to be tested for emissions. California
requires testing every two years, other states may
vary.
23. Install the two provided vent ttings into the
K&N
®
intake tube as shown.
NOTE: ON vehicles not equipped with an EVAP
vent line, install the npt plug inplace of the
5/16” vent tting.
NOTE: Plastic NPT ttings are easy to cross
thread. Install the vent tting “hand” tight, then
turn it two complete turns with a wrench.
24. Install the provided silicone hose (087121) onto
the K&N
®
intake tube and secure with the provided
hose clamp.
25. Install the K&N
®
intake tube assembly onto
the throttle body and into the silicone hose on
the lter adapter, then secure with the provided
hose clamps. Tighten the hardware securing the
mounting bracket to the heat shield.