Owners manual

ManualsBrandsK&N Filters ManualsAutomotive69-4523TP Typhoon Cold Air Induction Kit Fits 12-15 Camaro

69-4523TP

TOOLS NEEDED:

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST:

Description Qty. Part #

CHEVROLET

2012-14 Camaro

V6-3.6L

10mm Socket

13mm Socket

3mm Allen Wrench

4mm Allen Wrench

Extension

Flat Blade Screwdriver

Ratchet

2. Remove the oil ll cap and then lift up and

remove the engine cover. Reinstall the oil cap.

3. Slide the red locking tab back and then

disconnect the mass air sensor electrical

connection.

4. Disconnect the crank case vent hose from the

stock intake tube.

5. Loosen the hose clamp that secures the intake

hose to the throttle body.

6. Unlatch the upper air box clips and then remove

the upper air box and intake tube assembly.

A Hose Clamp # 48 1 08601

B Hose; 3-1/4” To 3” ID 90° Angled Molded 1 08629

C Hose Clamp # 52 2 08610

D Screw; M4-.7 X 12, Buttonhead SS 2 07726

E Intake Tube 1 27546TP

F Vent; STRT 1/2” Hose, 1/4” NPT 1 080022

G Hose; 1/2” ID X 3-1/2”L 1 087028

H Hose, Hump 3.25/3.50 X 3.00 1 5-576

I Hose Clamp # 56 1 08620

J Bolt; M6 X 1.00 X 16mm, Buttonhead, SS 4 07730

K Washer; 1/4” Lock, ZN 2 08198

L Washer; 6mm Flat, SS 7 08269

M Edge Trim (70”) 1 102454

N Heat Shield 1 074053

O Insert; 5/16-18 X 6.00 OD X .730L Rubber 1 088002

P Bracket; “Z”, STL, TK/PC 1 083126

Q Washer; 5/16” ID X 5/8” OD, Flat 1 08276

R Bolt; 5/16” -18 X 1” L, SS 1 07777

S Nut; 6mm Nylock, Hexhead 3 07553

T Washer; 1” X .300 X .100 Rubber 1 21685

U Adapter; Universal, 6” Filter 3.5” Coupler 1 21512-1

V Hose Clamp # 104 1 08697

W Air Filter 1 RC-5107

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Summary of content (3 pages)

PAGE 1
® 69-4523TP CHEVROLET A 2012-14 Camaro V6-3.6L G B M TOOLS NEEDED: 10mm Socket 13mm Socket 3mm Allen Wrench 4mm Allen Wrench Extension Flat Blade Screwdriver Ratchet E F C H I C K N L J D S J K J L L L W L O PARTS LIST: Description A B C D E F G H I J K L Hose Clamp # 48 Hose; 3-1/4” To 3” ID 90° Angled Molded Hose Clamp # 52 Screw; M4-.7 X 12, Buttonhead SS Intake Tube Vent; STRT 1/2” Hose, 1/4” NPT Hose; 1/2” ID X 3-1/2”L Hose, Hump 3.25/3.50 X 3.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Remove the lower air box mounting nuts and then remove the lower air box assembly. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 8. Remove the air box mounting grommet shown from the frame rail. 9. Install the heat shield mounting bracket (083126) onto the heat shield and secure with the provided hardware. 13.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 24. Reconnect the vehicle’s negative battery cable.