Owners manual
69-1211TTK
TOOLS NEEDED:
NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE
MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.
1. Turn off the ignition and disconnect the negative
battery cable.
NOTE: Disconnecting the negative battery
cable erases pre-programmed electronic
memories. Write down all memory settings
before disconnecting the negative battery cable.
Some radios will require an anti-theft coded to
be entered after the battery is reconnected. The
anti-theft code is typically supplied with your
owner’s manual. In the event your vehicles’
anti-theft code cannot be recovered, contact an
authorized dealership to obtain your vehicles
anti-theft code.
TO START:
PARTS LIST:
Description Qty. Part #
®
2. Disconnect the mass air sensor electrical
connection and then unhook the wiring harness
from air box.
3. Release the spring clamp and then disconnect
the crank case vent hose from the intake tube.
4. Release the two hose clamps securing the intake
tube to the air box and throttle body.
5. Remove the stock intake tube from the vehicle.
6. Unhook the wiring harness from the air box as
shown.
7. Loosen and remove the two air box mounting
bolts.
NOTE: The front air box mounting bolt is down
low next to the battery hold down.
8. Remove the complete air box assembly from the
vehicle.
NOTE: K&N Engineering, Inc., recommends that
customers do not discard factory air intake.
3mm allen wrench
10mm socket
10mm wrench
extension
at blade screw driver
phillips screw driver
pliers
ratchet
HONDA
2008-12 Accord
L4-2.4L
A Hose Clamp #44 1 08577
B Hose; 3” TO 2-3/4” ID X 2” L TPRD 1 084036
C Hose Clamp #48 2 08601
D Intake Tube 1 27430
E Vent; Strt. 1/2” Hose, 1/4”NPT, Plas. 1 080022
F Hose; 1/2” ID X 7” L 1 08159
G Bolt; M4 - 0.07 8MM, A/H CAP, SS 2 07733
H Hose Clamp #004 2 21850
I Hose; 1/4” ID X 10-1/2” L Reinforced 1 08400
J Bolt; 6MM-1.00 X 16MM, SS 4 07812
K Washer; 1/4” Lock, ZN 4 08198
L Washer; 1/4”ID X 5/8”OD - SAE 10 08275
M Bracket; “Z”, 69-1211, STL., TK/PC 1 070124
N Nut; 6MM Nylock, Hexhead, SS 3 07512
O Bracket; “L”, 69-1211, STL. TK/PC 1 070123
P Bolt; M6 X 1.00” X 20MM HEX, SS 3 07795
Q Heat Shield 1 073106
R Bracket; 69-6026, “Z”, STL., FB/PC 1 070061
S Edge Trim (39”) 1 102496
T Air Filter 1 RU-3570
A
B
C
F
E
G
H
I
H
J
K
L
J
K
L
M
N
L
N
L
O
J
K
L
P
L
P
L
C
K
L
J
N
R
L
T
S
D
Q
NOTE: Excludes LEV2 SULEV 2008-12
Test Groups: 8HNXV02.4EMC, 9HNXV02.4TC3
AHNXV02.4KC3, BHNXV02.4RC3 and
CHNXV02.4MC3