Owners manual

ManualsBrandsK&N Filters ManualsAutomotive69-1014TS Typhoon Cold Air Induction Kit Fits 06-11 Civic

TO START:

1. Turn the ignition off and disconnect the

vehicle’s negative battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

69-1014TS

HONDA

2006-11 Civic SI

L4-2.0L

Description Qty. Part #

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

2. Disconnect the mass air sensor electrical

connection. Un-clip the mass air sensor wiring

harness from the upper airbox.

3. Release the spring clamp, then disconnect the

EVAP canister hose from the intake tube as shown.

4. Release the crankcase breather hose spring

clamp. Release the hose clamp that secures the

intake tube to the throttle body.

5. Release the six upper airbox clips, then remove

the upper airbox and intake tube assembly as

shown.

NOTE: It is necessary to disconnect the

crankcase breather tube and un-hook the upper

radiator hose clip upon intake tube removal.

6. Remove the one nut and two bolts that secure

the lower airbox to the vehicle.

NOTE: This nut will be used again.

A Hose Clamp #40 2 08554

B Hose; 2-3/4" X 2"L, 1 08440

C Intake Tube 1 27535

D Hose; 5/8"ID X 10"L 1 5-7010

E Vent; 5/8 X 5/8 Plastic Elbow, BLK 1 08072

F Bolt; M4 - 0.07 8MM, A/H Cap, SS 2 07733

G Stud; 6MM-1.00 X 35MM L, SS 4 08220

H Washer; 6MM Flat, SS 6 08269

I Nut; 6MM Nylock, Hexhead, SS 5 07512

J Gasket; 1/16" Neoprene 2 09202

K Heat Shield 1 07354-1

L Edge Trim 1 102499

M Hose Clamp #52 1 08610

N Bracket; "L", STL, FB/PC 1 06507

O Bolt; 6MM-1.00 X 16MM, SS 1 07812

P Spacer; .625"OD X .375"ID X .625"L,ZN 1 07849

Q Adaptor; #350 1 21510

R Hose Clamp #80 1 08694

S Air Filter 1 RU-5147

T Hose; 5/16"ID X 17-1/4"L, EPDM 1 5-2017

U Hose Clamp #004 2 21850

V Hose Clamp #10 1 08411

Ratchet

Extension

10mm Socket

10mm Wrench

Pliers

Flat Blade Screw Driver

Phillips Screw Driver

3mm Allen Wrench

TOOLS:

PART LIST

Summary of content (3 pages)

PAGE 1
® 69-1014TS HONDA K 2006-11 Civic SI L4-2.0L H I V E I D TOOLS: Ratchet Extension 10mm Socket 10mm Wrench Pliers Flat Blade Screw Driver Phillips Screw Driver 3mm Allen Wrench O H G J IH G N Q P I H A B R J F A S H C G I H M G L U T PART LIST Description A B C D E F G H Hose Clamp #40 Hose; 2-3/4" X 2"L, Intake Tube Hose; 5/8"ID X 10"L Vent; 5/8 X 5/8 Plastic Elbow, BLK Bolt; M4 - 0.07 8MM, A/H Cap, SS Stud; 6MM-1.00 X 35MM L, SS Washer; 6MM Flat, SS U Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Un-hook the fresh air supply duct from the lower airbox as shown. 8. Remove the complete lower airbox assembly from the vehicle as shown. NOTE: K&N Engineering, Inc., recommends that you do not discard your factory air intake. 12. Install the provided bypass hose onto the throttle body and intake manifold ports. Secure with the provided hose clamps. 13.
PAGE 3
Continued INSTALLATION INSTRUCTIONS 27. Using a knife, cut the provided crankcase vent hose in 2.5” and 6.5” pieces as shown. 31. Replace any lost coolant into the cooling system per manufacturer’s instructions. 23. Install the provided spacer onto the airbox mounting stud as shown. 32. Reconnect the vehicle's negative battery cable. Check to ensure all hose clamps and fittings are properly tightened and positioned correctly before starting the vehicle. 28.