Owners manual

ManualsBrandsK&N Filters ManualsAutomotive63-3514 63 Series Aircharger Kit Fits 08 S2000

TOOLS NEEDED:

PARTS LIST:

Description Qty. Part #

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft coded to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

2. Release the 6 clips that retain the air box top,

then remove the top.

7. Loosen and remove the 3 bolts that secure the

air cleaner base, then remove the air cleaner base.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

13mm Socket

10mm Wrench

7/16” Socket

5/8”OD Drill Bit

Drill

Flat Blade Screwdriver

Pliers

Phillips Head Screwdriver

Ratchet w/Long Extension

Socket

Wire Cutters

A HOSE CLAMP #44 2 08577

B HOSE; 2.75”ID TO 3”ID HUMP 1 08421

C INTAKE TUBE 1 087042

D HOSE CLAMP #6 MINI 1 08407

E 1/4”ID X 10-1/2” SILICONE HOSE 1 08400

F HOSE, 1/2”ID X 14”L BLK. HOSE 1 08402

G HOSE 4MM ID X 18” BLK. SILICONE 2 08153

H HOSE CLAMP #004 2 21850

I HOSE CLAMP #48 1 08601

J SADDLE BRACKET 1 078855

K BOLT 6MM-1.00X20MM F/H/A SS 1 08376

L WASHER, CONICAL, NYLON, BLACK 1 08180

M BRACKET 1 08025

N WASHER, 1/4”ID X 5/8”OD, SAE 14 08275

O BOLT, M6-1.00X16MM HEXHD. TAP 7 07703

P NUT, 6MM NYLOCK HEXHD. 6 07553

Q WAVE WASHER 2 08174

R CABLE TIES, 12” BLACK 2 21590

S EDGE TRIM, 48”L 1 102485

T HEAT SHIELD 1 07458

U BRACKET LARGE “L” 1 08015

V FILTER ADAPTER 1 21561

W BRACKET, SMALL “L” 1 08023

X HOSE CLAMP, #64 1 08648

Y AIR FILTER 1 RP-4980

Z CAPLUG; .750”ID 1 08119

AA GROMMET;15/16”OD,3/8”ID,17/32” THK. 1 08100

AB CABLE TIES, 6” BLACK 1 21595

AC SCREW; M5-.8 X 20MM, BUTTON HEAD 1 22208

AD BRACKET; “L”, 63-2582, STL, TB/PC 1 083155

AE BOLT; HEX M6-1 X 35MM 1 1-2002

AF WASHER, M6 SPLIT LOCK ZINC 1 1-3025

AG SPACER: .625” OD X .250”ID X .250”L 1 06555

AH WASHER; 5MM FLAT, SS 2 08212

AI NUT; M5 - 0.8, NYLOCK, SS 1 07507

3. On vehicles equipped with air injection pump,

detach the air injection pump hose from the stock

intake tube.

4. Remove the crank case vent hardline from the

stock intake tube.

4a. On vehicles equipped with an air temperature

sensor, disconnect the air temperature sensor

electrical connection as shown.

5. Loosen the hose clamp at the throttle body, then,

remove the stock intake tube.

6. On vehicles equipped with air control solenoid,

loosen and remove the screw and push clip that

secures the air control solenoid valve to the air box

base.

8. Remove the crank case vent hose from the vent

on the cam cover.

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

63-3514

HONDA

2004-07 S2000

L4-2.0L

2008 S2000

L4-2.2L

Summary of content (3 pages)

PAGE 1
63-3514 A HONDA B S 2004-07 S2000 L4-2.0L 2008 S2000 L4-2.2L H A E C F G H Z D TOOLS NEEDED: T U 13mm Socket 10mm Wrench 7/16” Socket 5/8”OD Drill Bit Drill Flat Blade Screwdriver Pliers Phillips Head Screwdriver Ratchet w/Long Extension Socket Wire Cutters K J P O Q N O O M P N PARTS LIST: L N N X I N ON Y AB Q N N Description A B C D E F G H I J K L HOSE CLAMP #44 HOSE; 2.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 9. Detach the coolant hose from the fitting on the intake manifold, and from the fitting on the underside of the throttle body. 16. On vehicles equipped with air injection pump, attach the air control solenoid valve vacuum hose to the air control valve hard line. (lower hard line). 10. Detach the air control valve vacuum hose and the air control solenoid vacuum hose from the hard lines. 17.
PAGE 3
INSTALLATION INSTRUCTIONS Continued 26. Install the intake K&N® tube and secure the hump hose to the throttle body as shown. 26a. On vehicles equipped with an air temperature sensor, position the air temperature sensor wiring harness on the intake tube for best fit and mark the position on the intake tube with a marker for drilling. 28. On vehicles equipped with air injection pump, attach the air injection hose to the fitting on the K&N® intake tube.