Owners manual

ManualsBrandsK&N Filters ManualsAutomotive63-3074 63 Series Aircharger Kit Fits 10-15 Camaro

63-3074

TOOLS NEEDED:

PARTS LIST:

Description Qty. Part #

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

2. Disconnect the mass air sensor electrical

connection.

CHEVROLET

2010-15 Camaro SS

V8-6.2L

3mm Allen Wrench

4mm Allen Wrench

10mm Socket

13mm Socket

Extension

Flat Blade Screwdriver

Phillips Screwdriver

Ratchet

A HOSE CLAMP #64 STAINLESS 4 08645

B HOSE; 4” ID X 2” L 1 08761

C HOSE; 8MM ID X 21” L 1 08409

D VENT; STRT, 5/16” BARBED, 1/4 NPT 1 08908

E INTAKE TUBE 1 087232

F GASKET; 3/16 PORON 1 09069

G ADAPTOR; NYLON 6/6 GF, 1 21515

H BOLT; M4 - 0.07 8MM, A/H CAP, SS 2 07733

I WASHER; 6MM FLAT, SS 9 08269

J BOLT; M6 X 1.00 X 16MM , BTTNHD 6 07730

K HOSE; 4” ID X 3” L HUMP 1 08418

L WASHER; 1/4” LOCK, ZN 2 08198

M HEAT SHIELD 1 074053

N EDGE TRIM (70”) 1 102454

O NUT; 6MM NYLOCK, HEX 3 07512

P WASHER; 5/16”ID X 5/8”OD, FLAT 1 08276

Q WASHER; 1” X .300 X .100 RUBBER 1 21685

R BRACKET; “Z”, STL, TK/PC 1 083126

S INSERT; 5/16-18 X .600 OD X .730L 1 088002

T BOLT; 5/16”- 18 X 1”L, SS 1 07777

U ADAPTOR; #454 1 27300

V HOSE CLAMP # 104 1 08697

W AIR FILTER 1 RF-1042

3. Remove the oil ller cap and then lift up and

remove the engine cover. Reinstall the oil ller cap.

NOTE: On 2014 and later vehicles, the

manufacturer changed the crank case vent

system. The crank case vent tube will need to

be unhooked from the oil ller cap before the

cap can be removed from the engine.

4. Disconnect the crank case vent tube from the

intake resonator as shown.

5. Loosen the hose clamps which secure the stock

intake tube to the air box and throttle body.

6. Remove the stock intake tube as shown.

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Summary of content (3 pages)

PAGE 1
63-3074 CHEVROLET 2010-15 Camaro SS V8-6.2L A B C N D E TOOLS NEEDED: 3mm Allen Wrench 4mm Allen Wrench 10mm Socket 13mm Socket Extension Flat Blade Screwdriver Phillips Screwdriver Ratchet A O F G I P M J H Q I L U K J J V W I I O T R I PARTS LIST: Description A B C D E F G H HOSE CLAMP #64 STAINLESS HOSE; 4” ID X 2” L HOSE; 8MM ID X 21” L VENT; STRT, 5/16” BARBED, 1/4 NPT INTAKE TUBE GASKET; 3/16 PORON ADAPTOR; NYLON 6/6 GF, BOLT; M4 - 0.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Rotate the crank case vent tube 180°, then release the retainer at the valve cover port and then remove the crank case vent tube from the valve cover port. 13. Install the edge trim onto the heat shield as shown. NOTE: Some trimming of the edge trim will be necessary. 19. Install the provided gasket onto the mass air sensor adapter as shown. 8. Remove the two air box retaining nuts shown. 14.
PAGE 3
INSTALLATION INSTRUCTIONS Continued ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fix as necessary. 24.