Owners manual

ManualsBrandsK&N Filters ManualsAutomotive57-1571 57 Series Fuel Injection Performance Kit Fits 15-16 1500

FACTORY

PART

57-1571

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

NOTE: This kit was not designed

to t vehicles with a body lift.

RAM

2015-16 Ram 1500

V6-3.0L Turbo Diesel

Description Qty. Part #

A INTAKE TUBE (KD) 1 087298A

B HOSE CLAMP #52 3 08610

C HOSE; 3-1/4" ID X 2" L REIN 1 08690

D HOSE; 3.5"ID TO 3.25"ID X 2.5"L 1 08496

E HOSE CLAMP #56 1 08620

F BOLT; M6 X 1.00 X 16MM, SS 2 07730

G WASHER, M6 SPLIT LOCK ZINC 2 1-3025

H WASHER; 1/4"ID X 5/8"OD 2 08275

I EDGE TRIM (48") 1 102485

J ADAPTER; UNIVERSAL, 6", 3.5" 1 21512-1

K HEAT SHIELD 1 073187

L HOSE CLAMP # 104 1 08697

M FILTER CHARGER 1 RF-1042XD

PARTS LIST:

TOOLS NEEDED:

ratchet

extension

5/16” socket

at blade screw driver

t25 torx

4mm allen

2. Disconnect the mass air sensor electrical

connection.

3. Loosen the hose clamp securing the factory

intake tube to the mass air sensor.

4. Release the four clips securing the upper air

lter housing and then remove the housing and air

lter.

5. Lift up to dislodge the decorative engine cover

and then remove the cover.

6. Loosen the hose clamp securing the intake tube

to the turbo inlet hose. Lift up the intake tube to

dislodge it from the mounting stud and then remove

the tube from the vehicle.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

7. Install the provided coupling hose (08690)

halfway onto the K&N

intake tube and secure with

the provided hose clamp as shown.

8. Install the K&N

intake tube into the factory turbo

inlet hose and secure with the factory hose clamp.

9. Remove the mass air sensor from the factory

upper air lter housing.

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Summary of content (2 pages)

PAGE 1
57-1571 A RAM B 2015-16 Ram 1500 V6-3.0L Turbo Diesel C NOTE: This kit was not designed to fit vehicles with a body lift. FACTORY PART J TOOLS NEEDED: ratchet extension 5/16” socket flat blade screw driver t25 torx 4mm allen B B L PARTS LIST: D M H F Description E G H F I K Qty. Part # A INTAKE TUBE (KD) 1 087298A B HOSE CLAMP #52 3 08610 C HOSE; 3-1/4" ID X 2" L REIN 1 08690 D HOSE; 3.5"ID TO 3.25"ID X 2.5"L 1 08496 E HOSE CLAMP #56 1 08620 F BOLT; M6 X 1.
PAGE 2
INSTALLATION INSTRUCTIONS Continued 10. Install the provided coupling hose (08496) onto the mass air sensor as shown and secure with the provided hose clamp. 15. Reconnect the mass air sensor electrical connection. 18. Reconnect the vehicle’s negative battery cable. Double check to make sure everything is tight and properly positioned before starting the vehicle. 19. The C.A.R.B.