Owners manual

ManualsBrandsK&N Filters ManualsAutomotive57-1546 Filtercharger Injection Performance Kit Fits Dakota Raider

57-1546

TOOLS NEEDED:

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

1. Turn off the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery cable

erases pre-programmed electronic memories.

Write down all memory settings before

disconnecting the negative battery cable. Some

radios will require an anti-theft code to be

entered after the battery is reconnected. The

anti-theft code is typically supplied with your

owner’s manual. In the event your vehicles’

anti-theft code cannot be recovered, contact an

authorized dealership to obtain your vehicles

anti-theft code.

TO START:

PARTS LIST:

Description Qty. Part #

NOTE: This kit was not designed to

t vehicles with a body lift.

2005-10 Dakota

2006-07 Raider

V8-4.7L

DODGE / MITSUBISHI

10MM Socket

13MM Socket

1/2MM Socket

10MM Wrench

Extension

Flat Blade Screwdriver

Ratchet

A Hose Clamp #48 1 08601

B Hose; 3.5”ID to 3.25”ID Step 1 08051

C Hose Clamp #52 2 08610

D Intake Tube (FF) 1 087176

E Grommet; 1”OD, 1/2”ID, 1/2”Thk. 1 08064

F Hose; 1/2”ID x 9”L, Silicone 1 08401

G Saddle Bracket 1 078855

H Bolt; 6MM-1.00 x 20MM F/H/A, SS 1 08376

I Washer; Cup Black Nylon 1 08180

J Bracket 1 010128

K Washer; 1/4”ID x 5/8”OD, Flat 9 08275

L Nut; 6MM Nylock 5 07553

M Heat Shield 1 07663

N Edge Trim 55” 1 102480

O Lg. L Bracket 1 010124

P Bracket 1 010122

Q Lg. C Bracket 1 010123

R Bolt; 5/16”-18 x 1”L, SS 2 07777

S Washer; 5/16”ID x 5/8”OD, Flat 3 08276

T Bolt; 6MM-1.00 x 16MM 4 07703

U Insert; 5/16-18 x .600”OD x .730”l 2 088002

V Hose Clamp #56 2 08620

W Hose; 3.5”ID x 2”L, Silicone 1 08630

X Filter Adapter #380 1 21512-1

Y Hose Clamp #104 1 08697

Z Air Filter 1 RF-1048

AA Wire Extension 1 21680

2. Loosen the hose clamp at the throttle body and

the airbox mounting nut and then disconnect the

crankcase vent hose from the “tee” tting.

3. Disconnect the stock intake tube from the intake

plenum and lift to remove the airbox assembly from

the vehicle as shown.

4. Depress the locking tab on the air temperature

sensor electrical connection and then pull to

disconnect he sensor electrical connection.

5. Loosen and remove the two intake plenum

mounting bolts indicated

6. Lift and remove the intake plenum from the

vehicle as shown.

NOTE: K&N Engineering, Inc., recommends that

customers do not discard factory air intake.

7. Pull the two airbox mounting grommets shown

from the inner fender.

8. Install the provided edge trim onto the heat

shield as shown.

NOTE: Some trimming of the edge trim may be

necessary.

9. Install the “L” bracket (010124) onto the heat

shield with the provided hardware as shown.

Summary of content (3 pages)

PAGE 1
57-1546 PARTS LIST: DODGE / MITSUBISHI 2005-10 Dakota 2006-07 Raider V8-4.7L NOTE: This kit was not designed to fit vehicles with a body lift. TOOLS NEEDED: 10MM Socket 13MM Socket 1/2MM Socket 10MM Wrench Extension Flat Blade Screwdriver Ratchet AA Description Qty. A Hose Clamp #48 1 B Hose; 3.5”ID to 3.25”ID Step 1 C Hose Clamp #52 2 D Intake Tube (FF) 1 E Grommet; 1”OD, 1/2”ID, 1/2”Thk. 1 F Hose; 1/2”ID x 9”L, Silicone 1 G Saddle Bracket 1 H Bolt; 6MM-1.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 10. Install the “L” bracket (010122) onto the heat shield with the provided hardware as shown. 16. Twist the air temperature sensor counter clockwise and remove it from the stock intake plenum. NOTE: Take care, as the air temperature sensor is very fragile. 11. Install the “C” bracket (010123) onto the heat shield with the provided hardware as shown. 17. Install the provided grommet into the K&N® intake tube as shown. 12.
PAGE 3
Continued INSTALLATION INSTRUCTIONS ROAD TESTING: 1. Start the engine with the transmission in neutral or park, and the parking brake engaged. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, find cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 28. Install the air filter assembly onto the K&N intake tube and secure with the provided hose clamp as shown. ® 2.