Owners manual

ManualsBrandsK&N Filters ManualsAutomotive57-1002 Filtercharger Injection Performance Kit

FACTORY

PART

57-1002

TOOLS NEEDED:

PARTS LIST:

Description Qty. Part #

1. Turn o the ignition and disconnect the negative

battery cable.

NOTE: Disconnecting the negative battery

cable erases pre-programmed electronic

memories. Write down all memory settings

before disconnecting the negative battery

cable. Some radios will require an anti-

theft code to be entered after the battery is

reconnected. The anti-theft code is typically

supplied with your owner’s manual. In the

event your vehicles’ anti-theft code cannot be

recovered, contact an authorized dealership to

obtain your vehicles anti-theft code.

TO START:

2. Depress the wire-locking clip and disconnect the

mass air sensor electrical connection.

BMW 3 SERIES (E46)

1999-00 323i, ci

2001-05* 325i, ci

L6-2.5L

1999-00 328i

2000 328ci

2002-05 325xi

L6-2.8L

Flat Blade Screwdriver

Ratchet

Extension

10mm Socket

10mm Wrench

4mm Allen

A INTAKE TUBE 1 087139

B HOSE; 4MM ID X 2” L 1 08062

C NPT FITTING; 1/4” X 5/16” BARB 1 08908

D HOSE CLAMP #48 3 08601

E SILICONE HOSE 3.25”ID X 2”L 1 08690

F NUT; 6MM NYLOCK 7 07553

G WASHER; 1/4”ID X 5/8”OD FLAT 7 08275

H WASHER; 1/4” SPLIT LOCK 1 08198

I BOLT; 6MM-1.00 X 16MM, B/H/A 2 07730

J BOLT; 6MM-1.00 X 12MM, B/H/A 4 07794

K WASHER; 1/4”ID X 1”OD FENDER 2 08160

L BRACKET 1 010087

M HEAT SHIELD “A” 1 07492

N HEAT SHIELD “C” 1 07497

O HEAT SHIELD “B” 1 07494

P EDGE TRIM 46”L 1 102487

Q AIR FILTER 1 RU-4730

3. Pull up on the four fresh air duct-retaining pins

to release them from the radiator core support.

4. Lift up and remove the fresh air duct from the

vehicle as shown.

NOTE: Disconnect the fresh air tube from the

fresh air duct.

5. Loosen the hose clamp that secures the

intake tube to the mass air sensor and then

disconnect the intake tube from the mass air

sensor as shown.

6. Remove the two factory air box mounting bolts

shown.

NOTE: * Excluding 2005 PZEV

model with engine family

5BMXV02.5M56

NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE

MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE.

If you need any assistance please call 1-800-858-3333 to speak with a representative

in our Customer Service Center before returning the product.

Summary of content (3 pages)

PAGE 1
57-1002 BMW 3 SERIES (E46) 1999-00 323i, ci 2001-05* 325i, ci L6-2.5L 1999-00 328i 2000 328ci 2002-05 325xi L6-2.8L FACTORY PART NOTE: * Excluding 2005 PZEV model with engine family 5BMXV02.5M56 TOOLS NEEDED: Flat Blade Screwdriver Ratchet Extension 10mm Socket 10mm Wrench 4mm Allen PARTS LIST: Description A B C D E F INTAKE TUBE HOSE; 4MM ID X 2” L NPT FITTING; 1/4” X 5/16” BARB HOSE CLAMP #48 SILICONE HOSE 3.25”ID X 2”L NUT; 6MM NYLOCK Qty.
PAGE 2
Continued INSTALLATION INSTRUCTIONS 7. Unhook the wiring harness from the rear of the factory air box. 8. Lift up and remove the air box from the vehicle. NOTE: K&N Engineering, Inc., recommends that customers do not discard factory air intake. 13. Install the K&N® intake tube into the factory lower intake hose and secure with the factory hose clamp. NOTE: Do not completely tighten the hose clamp at this time. 14. Remove the factory fresh air hose from the air box as shown. 9.
PAGE 3
INSTALLATION INSTRUCTIONS Continued 24. Reinstall the lower rubber air box locator removed in step #11 and re-secure the heater hose. 28. Reinstall the fresh air duct removed in step #4 and secure with the four factory retaining pins. 32. Reconnect the vehicle’s negative battery cable. Double check to make sure everything is tight and properly positioned before starting the vehicle. 33. The C.A.R.B.