Kobra KK52/KK102 USER’S MANUAL English
KK52/KK102 Contents SYMBOLS 5 1. INTRODUCTION 7 2. APPLICATIONS 7 3. KEY FEATURES 7 4. UNPACKING 8 5. WARRANTY 8 6. SAFETY 8 7. PHYSICAL 9 8. REAR PANEL 11 9. COVERAGE 12 10. WIRING 14 11. PROTECTION CIRCUITRY 14 12. ACCESSORIES AND CONFIGURATIONS 15 K-Base2 15 K-Fly2 16 K-Joint2 16 K-Wall2L 17 K-Wall2 17 K-KCluster2 / K-PCluster2 18 K-Foot2 18 K-KStage2 / K-PStage2 19 13. SERVICE 19 14. Specifications 20 REV.
KK52/KK102 4 REV.
KK52/KK102 SYMBOLS K-array declares that this device is in compliance with applicable CE standards and regulations. Before putting the device into operation, please observe the respective country-specific regulations! WEEE Please dispose of this product at the end of its operational lifetime by bringing it to your local collection point or recycling center for such equipment. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature.
KK52/KK102 6 REV.
KK52/KK102 1. INTRODUCTION The K-array Kobras are passive speaker systems, comprised of 2” neodymium magnet transducers housed in an elegant and sturdy stainless steel chassis. Available in two lengths, the KK52 features 8 drivers in a 0.5 m (19.7”), while the KK102 features 16 drivers a 1 m (39.4”) chassis. The vertical dispersion pattern can be switched for wide or narrow coverage, allowing for a great variety of applications.
KK52/KK102 4. UNPACKING Each K-array loudspeaker is built to the highest standard and thoroughly inspected before leaving the factory. Upon arrival, carefully inspect the shipping carton, then examine and test your new loudspeaker. If you find any damage, immediately notify the shipping company. Only the consignee may institute a claim procedure regarding the system’s electronic equipment. 5.
KK52/KK102 7. PHYSICAL KK52 5.9 cm 2.32” 50 cm 19.7” 12 cm 4.72” 8.1 cm 3.19” weight: 2.3 kg (5.07 lbs) REV.
KK52/KK102 5.9 cm KK102 2.32” 2.75 cm 1.08” 100 cm 39.4” 12 cm 4.72” 2.75 cm 1.08” weight: 4.8 kg (10.58 lbs) 8.1 cm 3.19” 10 REV.
KK52/KK102 8. REAR PANEL 1 2 3 1 1) Mounting screw holes. Most K-array mounting or flying accessories are designed to screw into the speakers using these holes. The KK52 is equipped with two screw holes, while the KK102 is equipped with four. 2) Impedance switch. Selects the impedance of the speaker. Impedance must be set to high (64 Ω for KK52 and 32 Ω for KK102) when speakers are driven by KMT active modules.
KK52/KK102 9. COVERAGE Img1: Flood coverage Img2: Spot coverage 12 REV.
KK52/KK102 Img3: Array - spot coverage Img4: Array - Downfill application REV.
KK52/KK102 10. WIRING Kobra KK52 and KK102 internal wiring is designed to pick up audio power signal from pins 1+ / 1- of a NL4 connector. 2+ and 2- pins, such as 1+ and 1-, are directly wired from one socket to the other, so signal can pass through multiple KK modules without additional external cabling. 11. PROTECTION CIRCUITRY Speakers are electrically protected from brief power overloads, within a reasonable range.
KK52/KK102 12. ACCESSORIES AND CONFIGURATIONS K-array offers a variety of dedicated accessories to mount and interconnect KK (Kobra) and KP (Python) series speakers for a wide array of possible configurations. K-Base2 Standing accessory for KK/KP speakers. For proper installation and operation, use with K-Foot2 and K-Joint2. TIPS: where possible, screw the feet of K-Base2 to the ground.
KK52/KK102 K-Fly2 Flying accessory set for KK/KP speakers. For proper installation and operation, use with K-Joint2. K-Joint2 WARNING Consult the dedicated product manual for safety information and operation details. K-Joint2 Attachable joint to link a KK/KP speaker to most accessories or to another KK/KP speaker with continuously variable angle (-10° <. . . . > 10°). 16 REV.
KK52/KK102 K-Wall2L Wall / stand mounting accessory for KK/KP speakers with bi-dimensional tilting features. K-Wall2L is designed to be screwed directly to the mounting screw holes of KK/KP speakers. When used with KK102 it can be screwed to the internal or the external screw holes depending on the width of the desired angle. K-Wall2 Wall mounting accessory for KK/KP speakers with full 3-dimensional tilting features.
KK52/KK102 K-KCluster2 / K-PCluster2 Wall mounting accessory for a horizontal cluster of three KK52/102 speakers. K-KCluster 2 / K-PCluster 2 comes in a set of three different models: one with no angle between the three hanging speakers, one with a 30° angle between speakers, one with a 60° angle between speakers. 0° 0° 30° 30° 60° 60° K-Foot2 35 mm pole mounting accessory. A 35 mm threaded pole is included for connecting additional K-array products such as KMT subwoofers or K-Base2. 18 REV.
KK52/KK102 K-KStage2 / K-PStage2 Ground laying accessories for KK/KP series speakers. K-KStage 2 / K-PStage 2 allow users to safely lay KK / KP series speakers on the ground with three different angles: 0°, 30° and 45°. Ideal applications are monitoring and front-fill. 13. SERVICE To obtain service: 1) Contact the official K-array distributor in your country. Your local distributor will direct you to the appropriate service center.
KK52/KK102 14. Specifications KK52 Acoustics Speakers power handling 200 W (AES) Max power 400 W 1 Impedance 16Ω or 64Ω (selectable) Frequency range 150 Hz - 20 KHz. SPL 1W / 1mt 95 dB 2 Maximum SPL 118 dB continuous - 124 dB peak Coverage Horizontal Vertical 110° 10°- 60° (selectable) Crossover Type Frequency External Crossover required High pass @150 Hz, 24 dB/oct suggested minimum Transducers Full range 8 x 2” Neodymium magnet with 0.
KK52/KK102 KK102 Acoustics Speakers power handling 400 W (AES) Max power 800 W 1 Impedance 8Ω or 32Ω (selectable) Frequency range 150 Hz - 20 KHz. SPL 1W / 1mt 98 dB 2 Maximum SPL 124 dB continuous - 130 dB peak Coverage Horizontal Vertical 110° 7°- 35° (selectable) Crossover Type External Crossover required Frequency High pass @150 Hz, 24 dB/oct suggested minimum Full range 16 x 2” Neodymium magnet with 0.
KK52/KK102 22 REV.
KK52/KK102 The contents of this manual are furnished for informational purposes only. Hp Sound Equipment s.r.l. assumes no responsibility for any errors or inaccuracies that may appear in this manual. Hp Sound Equipment s.r.l. reserves the right to make modifications without prior notice. REV.
UMC029AA01ENA K-array s.r.l. unipersonale Via Paolina Romagnoli - 50037 San Piero a Sieve (Firenze) - Italy tel. +39 055 8487222 - fax. +39 0558487238 e-mail: info@k-array.com www.k-array.
