User Manual

EV-TX-3000 Installation Manual… 7
DRAFT-REVC
_______________________________________________________________
2617 JUAN TABO NE SUITE A, ALBUQUERQUE, NM 87112 PHONE
888.536.5207 FAX [phone] [e-mail]
EYE-View™ Transmitter Model No: EV-TX-3000 FCC ID: OPH-EV3000
S/N: EV-TX-XXXXXX
Made in USA
K&A WIRELESS, LLC
White - Audio (Optional)
Blue - Channel Change (Optional)
MMCX Ant.
Connector
Solder
5 Plcs
Min.
WIRE COLOR
Violet - Video Ground
Yellow - Video In
Black - Ground
Red - Power
ON
213
SIDE
P
R
O
P
R
I
E
T
A
R
Y
ON
Additional Feature; Do Not Move OFF
SWITCH CONFIGURATION (See Diagram)
On the Fly (OTF) Channel Select
(Option with Blue Wire)
Channel Select 2 (Freq. 2.474 GHz)
Channel Select 1 (Freq. 2.458 GHz)
Solder
5 Plcs
Min.
2 Plcs
WARRANTY VOID
IF LABLE CUT OR
REMOVED
K&A Wireless, LLC
www.ka-wireless.com
1
Power Adj.
CW-Increase
FM ANALOG TRANSMITTER 2 CH
FM-TX-S-3002
Albuquerque NM 87112
K&A Wireless, LLC
SW1 SW2 SW3
OFF OFF
Switch configuration shown is Ch. 1
2
3
OFF OFF
OFF ON
TOP
BOTTOM
A Original 03/27/06
Figure 2. Photo and K&A drawing for EV-TX-3000.
The transmitter is supplied with a K&A antenna (part #: TX-
S-2018-MMCX-RTA) to comply with FCC regulations, as
shown in Figure 2. Any attempt to operate the system without
an antenna or an antenna that is not approved by K&A, in
writing, will result in damage to the system and will nullify
any warranty and MAY VIOLATE FCC LICENSE
AGREEMENT.
P/N TX-S-2018-MMCX-ST = STRAIGHT MMCX CONNECTOR
P/N TX-S-2018-MMCX-RT.A = RIGHT ANGLE MMCX CONNECTOR
2) CABLE LENGTH CAN BE MODIFIED TO MEET CUSTOMERS NEEDS.
Optional Cable Location
1) OPTIONAL ANTENNA TYPES
NOTES:
SIDE VIEW
TX-S-2018-MMCX
Optional Termination
MMCX
Straight
MMCX
Right
Angle
Albuquerque NM 87112
K&A Wireless, LLC
Disk Antenna
Hold Down
Straps
ANTENNA
SOLDERED
3 PLC.
Figure 3. K&A drawing for antenna provided with EV-
TX-3000 series transmitter.
EV-TX-3000 Installation Manual… 8
DRAFT-REVC
_______________________________________________________________
2617 JUAN TABO NE SUITE A, ALBUQUERQUE, NM 87112 PHONE
888.536.5207 FAX [phone] [e-mail]
Transmitter Installation
The transmitter is designed to be integrated into your camera
system. To install the transmitter, connect the red wire to the
battery (or regulator output), connect the black wire to ground
or the negative terminal of your battery (or regulator output).
For the video connection, you should have requested either a
high-Z or low-Z video input. This is the termination setting. If
a low-Z input is required (this is in cases where the camera is
directly tied to the transmitter with no other connections), the
transmitter will measure approximately 75ohms at the video
leads. In this case, confirm that the voltage coming from the
camera does not exceed
1Vp-p. FAILURE TO DO SO
WILL VIOLATE FCC LICENSE APPROVAL.
In cases where a high-Z setting is requested, (when the camera
is required to drive a monitor and a transmitter without any
video buffer amplifiers in the camera), the video input on the
transmitter will measure approximately 1kOhm. In this case,
confirm that both the monitor (or load) is connected and the
transmitter is also connected. Measure the impedance of the
parallel combination and confirm that is measures
approximately 75ohm. Connect the video to the camera
(confirm that the yellow transmitter video wire is connected to
the positive video connection on the camera). In this case,
confirm that the video level at the transmitter does not exceed
1Vp-p. FAILURE TO DO SO WILL VIOLATE FCC
LICENSE APPROVAL.
Apply power to the camera and confirm that the camera is
functional. Apply power to the transmitter and you should
have a picture on the receiver unit (K&A EV-RX-2XXX
series receiver units). If there is not picture, see the
troubleshooting section of this manual. Additional
documentation may be provided for specific installations.