User Guide

ManualsBrandsJW Speaker ManualsHeadlight AssembliesJW Speaker LED Headlights, Model 8700 Evolution J2 Series with CARBON FIBER Bezel, Set of 2

J.W. Speaker Corporation • Germantown, WI U.S.A. • www.jwspeaker.com • speaker@jwspeaker.com • 262.251.6660

Rev: 11/15/2017

Model 8700 Evolution J2

LED Headlight Instruction Sheet

INSTRUCTION INFORMATION

Tools Needed

Phillips screwdriver

Flat blade screw driver

T15 Torx driver

Estimated Time 30 minutes

Wire Functions (All)

ECE Versions Only

Black = Ground

White = High Beam

Yellow = Low Beam

Red = Front Position

Blue = Daytime Running Light (DRL)

In the Box (x2) Model 8700 Evolution J2 Headlights (Kit)

INSTRUCTIONS BEGIN ON THE NEXT PAGE

Page 1

Input Voltage

Operating Voltage

12V DC

9-16V DC

Pre-Installation Guidelines

To properly install this light you should have a good

understanding of automotive electrical procedures and

systems, and proﬁciency in the installation of headlights.

IF YOU DO NOT, PLEASE SEEK PROFESSIONAL ASSISTANCE.

1. Read all safety notes and mounting guidelines before installing

the product. Verify that all parts listed under “In the Box” are

present and complete.

2. Inspect the product for damage. DO NOT install the product if

there is any damage. Contact the authorized retailer where you

purchased it to initiate a warranty claim if there is damage.

3. Verify that all power supply and/or charging systems comply to

the speciﬁed voltage limits for the light.

PRODUCT WARRANTY:

If you have issues with a J.W. Speaker

product, please contact the authorized

retailer where you purchased it.

Regulatory Compliance

Summary of content (5 pages)

PAGE 1
Model 8700 Evolution J2 LED Headlight Instruction Sheet INSTRUCTION INFORMATION Estimated Time 30 minutes Tools Needed Phillips screwdriver Flat blade screw driver T15 Torx driver In the Box (x2) Model 8700 Evolution J2 Headlights (Kit) Wire Functions (All) Black = Ground White = High Beam Yellow = Low Beam Red = Front Position Blue = Daytime Running Light (DRL) ECE Versions Only Regulatory Compliance Input Voltage 12V DC Operating Voltage 9-16V DC To properly install this light you should hav
PAGE 2
Installation Instructions 1. Loosen the Phillips head screws in the fasteners that secure the top of the grill. NOTE: Some model years have fasteners that have a center post to pry out instead of screws. 2. Carefully remove the 6 fasteners by prying them up at the base using a ﬂat blade screw driver. Save the 6 fasteners. 3. Carefully remove the front grill by pulling the TOP portion forward until it unsnaps. Start near one headlight and work across to the other light. 4.
PAGE 3
7. Unplug the existing headlight. NOTE: On newer models there is (1) a red button on the plug that must be pushed up, and (2) a green button that must be pressed and held to unplug the existing lamp. 8. Plug in the new LED headlight and install it into the mounting ring. NOTE: On ECE versions, connect the RED wire for Front Position and the BLUE wire for DRL. 2 1 9. Align the alignment lugs on the lamp with the slots in the ring.
PAGE 4
Low OR High/Low Beam Headlight Aiming Instructions HEADLIGHTS MUST BE AIMED AFTER INSTALLATION. Headlight must be securely mounted and properly aimed such that the beam pattern “cut oﬀ line” complies with all applicable regulations. If you are not familiar with the legal requirements for aiming your headlights, please see a professional service provider. We recommend that headlights are aimed with a headlight aiming system for proper alignment.
PAGE 5
Low OR High/Low Beam Headlight Aiming Instructions 3. Connect the center points between headlights in a straight line, using chalk or tape. This will create your X axis (horizontal) line. NOTE: Use a straight edge and a level to make sure this line is straight. Y X Y 4. Extend your vertical, Y (vertical) axis lines up approximately 3 feet. Your lines should match the diagram below, when looking at the lines straight on. Y Y X 5.