WB-S681U WB-S682U WB-S684U WB-S685U Pendant Mount Wall Mount Outdoor Pendant Mount Ceiling Recessed Bracket WB-S681U WB-S681 INSTRUCTIONS Thank you for purchasing this product. To obtain the best results from your bracket, read these instructions carefully before use; retain the manual for future reference. The "INSTRUCTIONS" section below is applicable to WB-S681U/WB-S682U/WB-S684U/WB-S685U. Please refer to the installation procedures for the purchased product during installation.
IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to. 4. Unplug this appliance system from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 5. Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. 6.
Operating Precautions For safety reasons special techniques are necessary for installation. Consult your dealer regarding installation, and ensure that it is carried out by a specialist. Be sure to mount the safety wire for safety purposes. If it falls, it may cause injury or accidents. As the combination camera rotates at high speed, ensure that you install the camera at a location with sufficient strength to support the vibration and weight.
WB-S681U Pendant Mount Notes on Installation ● Check that the installation location is able to withstand the total weight of the camera, which is about 3.7 kg, before you install. If the location is not strong enough, reinforce with a reinforcing board. ● Always use a wire rope to install. ● Screws to secure WB-S681U to the ceiling are not provided. Use the appropriate screws based on the materials, structure and total weight of the installation location.
WB-S682U Wall Mount Notes on Installation ● Check that the installation location is able to withstand the total weight of the camera, which is about 2.9 kg, before you install. If the location is not strong enough, reinforce with a reinforcing board. ● Always use a wire rope to install. ● Screws to secure WB-S682U to the wall are not provided. Use the appropriate screws based on the materials, structure and total weight of the installation location.
WB-S684U Outdoor Pendant Mount Notes on Installation ● ● ● ● Consult your dealer on the installation location. We will not be responsible for any accidents that occur as a result of flawed installation. Pay due attention to the installation location and method. If the location is not strong enough, reinforce with a reinforcing board and check for safety before installing. WB-S684U is an outdoor model. WB-S684U is exclusively used for VN-V686WPU and TK-C686WPE (For Europe). 1.
5. Make a hole in the ceiling. 6. Thread the cables on 5. 40 mm the ceiling. Mount WB-S684U on the ceiling. (4 locations) 6. CAUTION • Use waterproof material to seal around the mounting surface of WB-S684U. • Use GE silicon or its equivalents as the sealing material. Bolts (M6~M8) or Anchor Bolts (M8) Making a hole in the ceiling 7. Fall prevention wire hole When a hole cannot be made in the ceiling Remove the cap and thread the cables. (Thread the coaxial cable first.
WB-S684U Outdoor Pendant Mount (continued) 8. Install the fall prevention wire on WB-S684U. A Thread the ring section of the fall prevention wire B Connection section fixing screws that was removed in step 4 through the fall prevention wire hole of WB-S684U. Thread the terminal side twice through the ring in A. 11. Thread twice 10. Fall prevention wire 9. Install the fall prevention wire to the camera unit.
WB-S685U Ceiling Recessed Bracket (Not for USA and Canada) Notes on Installation ● Check that the installation location is able to withstand the total weight of the camera, which is about 2.9 kg, before you install. If the location is not strong enough, reinforce with a reinforcing board. ● The unit can be installed on ceilings of thickness up to 35 mm. ● Always use anchor bolts to secure WB-S685U. If anchor bolts are unavailable, be sure to use wire rope.
WB-S685U Ceiling Recessed Bracket (Not for USA and Canada) (continued) Front side of camera 5. Connect the cable. 5. 7. Cable Connect the cable to the terminal block of the ceiling attachment fitting. 6. Mount the ceiling Fall prevention wire of the camera attachment fitting on WB-S685U. (3 locations) CAUTION Ensure that the fall prevention wire is secured at the positions shown above. CAUTION Ensure that the cable is not caught in between during installation. 7. Install the fall prevention wire.
Dismantling the camera 1. Remove the ceiling panel. Release lever 2. Remove the camera from WB-S685U. 2. 2. Release lever Press Press Press the release lever and remove. CAUTION Release lever Always support the camera with the palm of your hand when performing this operation. Press 3. Remove the fall prevention wire. Dismantling WB-S685U 1. Remove the ceiling attachment fitting and the cable. Remove in the reverse procedure of mounting. 3. Stopper Stopper release lever 2.
Specifications WB-S681U Operating temperature WB-S682U WB-S685U WB-S684U (Not for USA and Canada) Outdoor Temperature at guaranteed performance: 30 C ~ +40 C Temperature at guaranteed operation: 40 C ~ +50 C Indoor Temperature at guaranteed performance: 0 C ~ +40 C Temperature at guaranteed operation: 10 C ~ +50 C Mass (Body) Approx. 1.7 kg Approx. 0.9 kg Approx. 0.8 kg Accessories Instructions.................1 Instructions ................ 1 Screw (M4).................3 Nut (M4).......
安全上のご注意 (WB-S681,WB-S682,WB-S685) この取扱説明書および製品への表示では、製品を安全に正しくお使いいただき、あなたや他の人々への危害や財産への損害 を未然に防止するために、いろいろな絵表示をしています。その表示と意味は次のようになっています。内容をよく理解し てから本文をお読みください。 この表示(文字含む)を無視して、誤った取り扱いをすると、人が死亡または重傷を負う可能性が 想定される内容を示しています。 この表示(文字含む)を無視して、誤った取り扱いをすると、人が傷害を負ったり、物的損害の発 生が想定される内容を示しています。 絵表示の表示例 記号は、注意(警告を含む)を促す内容があることをお知らせするものです。図の中に具体的な注意内容 (左図の場合は指を挟まれないよう注意)が描かれています。 記号は、禁止の行為であることをお知らせするものです。図の中や近傍に具体的な禁止内容 (左図の場合は分解禁止)が描かれています。 警告 䡵 安全のため設置には特別な技術が必要です。取り付けについては、お買い上げ販売店にご相談ください。 䡵 安全ワイヤーは安全のため必ず取り付けてくだ
安全上のご注意 (WB-S684) この取扱説明書および製品への表示では、製品を安全に正しくお使いいただき、あなたや他の人々への危害や財産への損害 を未然に防止するために、いろいろな絵表示をしています。その表示と意味は次のようになっています。内容をよく理解し てから本文をお読みください。 この表示(文字含む)を無視して、誤った取り扱いをすると、人が死亡または重傷を負う可能性が 想定される内容を示しています この表示(文字含む)を無視して、誤った取り扱いをすると、人が傷害を負ったり、物的損害の発 生が想定される内容を示しています 絵表示の表示例 記号は、注意(警告を含む)を促す内容があることをお知らせするものです。図の中に具体的な注意内容 (左図の場合は指を挟まれないよう注意)が描かれています。 記号は、禁止の行為であることをお知らせするものです。図の中や近傍に具体的な禁止内容 (左図の場合は分解禁止)が描かれています。 警告 䡵 安全のため設置には特別な技術が必要です。取り付けについては、お買い上げ販売店にご相談ください。 䡵 安全ワイヤーは安全のため必ず取り付けてください。落下するとけがや事故の原因とな
WB-S681 天井吊下げポール 設置上のお願い ● 設置場所は、カメラ取り付け時の総質量(約 3.7 kg)に十分耐えられる強度を持っていることを確認してから取り 付けてください。強度が保てない場合は、補強板などで補強してください。 ● 必ず安全ワイヤーを使用して取り付けてください。 ● WB-S681 を天井に固定するネジは付属していません。取付場所の材料や構造、総質量を考慮してご用意ください。 ● 設置、工事の際は、現地の基準に従って行なってください。 1. 天井に穴を開ける Φ40 mm 1. カメラ正面 2. 2. ケーブルと安全ワイヤー を通す ボルト(M5∼M6) 天井取付 ブラケット 3. カバーを矢印方向(↓)に 6. 安全ワイヤーを取り 4. 付ける(1個所) ずらす (詳細は、カメラの「取扱説明書」 をご覧ください。) カバー 4. 天井取付ブラケットを天井 3. 5. 7. ケーブルを接続する に取り付ける(4個所) 天井取付金具の端子台に ケーブルを接続します。 (詳細は、カメラの「取扱説明書」 をご覧ください。) 5.
WB-S682 壁面取付けブラケット 設置上のお願い ● 設置場所は、カメラ取り付け時の総質量(約 2.9 kg)に十分耐えられる強度を持っていることを確認してから取り 付けてください。強度が保てない場合は、補強板などで補強してください。 ● 必ず安全ワイヤーを使用して取り付けてください。 ● WB-S682 を壁面に固定するネジは付属していません。取付場所の材料や構造、総質量を考慮してご用意ください。 ● 設置、工事の際は、現地の基準に従って行なってください。 6. カメラ正面 袋ナット(M4) (付属品) 安全ワイヤー ネジ(Φ5 mm∼Φ6 mm) または ボルト(M4∼M6) 2. 1. Φ 30 mm 3. 1. 5. 壁に穴を開ける 4. 2. 3. ケーブルを WB-S682に通す 天井取付金具の端子台に ケーブルを接続します。 ネジ(M4) 6. 5. 天井取付金具をWB-S682 に取り付ける(3個所) 袋ナットを取り付けます。 (3個所) WB-S682を壁面に 取り付ける(4個所) 天井取付金具 7. 4.
WB-S684 屋外用天井吊下げポール 設置上のお願い ● ● ● ● 設置場所は、お買い上げの販売店とよく相談してください。 取り付けの不備などによる落下事故の責任は一切負いかねます。 設置場所や設置方法に十分に注意をしてください。 設置場所の強度が保てない場合は、補強板などで補強し、安全を確認の上、取り付けてください。 ● ● WB-S684は、屋外専用です。 WB-S684はVN-V686WP、TK-S686WP専用です。 トップカバー 1. カメラ部よりトップカバーをはずす A B トップカバー固定ネジをはずします。 C トップカバーを上に持ちあげながら カメラ部 トップカバー 固定ネジ トップカバーを右図のように 反時計方向に回します。 はずします。 2. アーム部からカメラ部をはずす アーム部 接続部固定ネジをはずします。(3個所) 接続部 固定ネジ 2. レンチ (4 mm) 1. 3. アーム部からケーブルと トップカバー トップカバー 落下防止ワイヤーを引き出す ご注意 ● カメラ部 ケーブルを傷つけないように引き出してください。 4.
WB-S684 5. 屋外用天井吊下げポール(つづき) 天井に穴を開ける 6. 天井にケーブル類を通す 7. 天井にWB-S684を取り付ける (4個所) 5. Φ40 mm 6. ご注意 WB-S684の取り付け面のまわりを防水シール材 でふさいでください。 ボルト(M6∼M8) または アンカーボルト(M8) 天井に穴を開ける 7.
8. 落下防止ワイヤーをWB-S684に取り付ける A 手順4で取りはずした落下防止ワイヤーの輪の部分を、 B 接続部固定ネジ WB-S684の落下防止ワイヤー取付穴に通します。 Aの輪に、端子側を2回通します。 11. 2回通す 10. 安全ワイヤー 9. 落下防止ワイヤーをカメラ部に取り付ける A 輪に通した端子側をカメラ部の方向に引っ張ります。 B 手順4で取りはずした落下防止ワイヤー固定ネジを 使って、落下防止ワイヤーをカメラ部に取り付けます。 落下防止 ワイヤー 固定ネジ 落下防止ワイヤー 10. ケーブルを接続する VN-V686WPまたはTK-S686WPの取扱説明書をご覧ください。 ご注意 使用しないケーブル類の先は、必ず1本ずつ 絶縁テープを巻いて処理してください。 11. カメラ部を取り付ける ケーブルをWB-S684のアーム部に押し込み、 手順2ではずした接続部固定ネジ(3本) を使って取り付けます。 12.
WB-S685 天井埋込ブラケット 設置上のお願い ● 設置場所は、カメラ取り付け時の総質量(約 2.9 kg)に十分耐えられる強度を持っていることを確認してから取り 付けてください。強度が保てない場合は、補強板などで補強してください。 ● 取り付け可能な天井の厚さは 35 mm までです。 ● WB-S685 は必ず、アンカーボルトで固定してください。アンカーボルトが使用できない場合は、必ず安全ワイ ヤーを使用してください。 ● 設置、工事の際は、現地の基準に従って行なってください。 取り付けかた 固定金具 固定ネジ(3個所)を反時計方向 に回し、固定金具を右図のように 上に移動しておきます。 固定ネジ ドライバー 反時計方向 にまわす 1. Φ200 mm ストッパー 1. 2. 天井に穴を開ける 天井 5 mm∼35 mm 付属のテンプレートを 使います。 2. ストッパーで、天井に WB-S685を仮固定する 3. アンカーボルトでWB-S685 を天井に固定する 4.
カメラ正面 5. ケーブルを接続する 5. 7. ケーブル 天井取付金具の端子台に ケーブルを接続します。 6. 天井取付金具を WB-S685に取り付ける (3個所) カメラ本体の 落下防止ワイヤー ご注意 ●落下防止ワイヤーが、上図の ご注意 位置で抜けないことを確認し てください。 ケーブルをはさまないように 取り付けてください。 7. 8. 落下防止ワイヤーを取り 付ける 6. 天井取付金具 ネジ(M4) (付属品) 落下防止ワイヤー 8.
WB-S685 天井埋込ブラケット(つづき) カメラの取りはずしかた 1. 天井パネルをはずす リリース レバー 2. カメラ本体をWB-S685 リリース 2.レバー 2. 押す 押す から取りはずす リリースレバーを押して 取りはずします。 ご注意 リリース レバー 必ずカメラ本体を手のひらで支え ながら行なってください。 押す 3. 落下防止ワイヤーを はずす WB-S685の取りはずしかた 1. 天井取付金具とケーブル をはずす 取り付けと逆の手順で はずします。 2. 3. ストッパー ストッパー 解除レバー 固定ネジ(3個所)を 反時計方向に回す 3. ストッパーをはずす 2. 押し上げる ドライバー ストッパー解除レバー をドライバーなどで 押し上げます。 反時計方向に まわす。 ドライバー ご注意 必ずWB-S685を支えながら行なって ください。 4. 天井からWB-S685を取りはずす 22 4.
仕様 WB-S681 周囲温度 WB-S682 WB-S685 WB-S684 屋外 性能保証温度:ⴑ30 ⴗC ∼ +40 ⴗC 動作保証温度:ⴑ40 ⴗC ∼ +50 ⴗC 屋内 性能保証温度: 0 ⴗC ∼ +40 ⴗC 動作保証温度: ⴑ10 ⴗC ∼ +50 ⴗC 質量(本体のみ) 付属品・添付物 約 1.7 kg 約 0.9 kg 約 0.8 kg 約 1.3 kg 取扱説明書 .......................... 1 取扱説明書.......................... 1 取扱説明書 ..........................1 取扱説明書 .......................... 1 ネジ (M4) ........................... 3 ナット (M4) ....................... 3 テンプレート ......................1 ネジ (M5) ........................... 3 安全ワイヤー (750 mm) .....
WB-S681U/WB-S681 WB-S682U/WB-S682 WB-S684U/WB-S684 WB-S685U/WB-S685 LST0643-001C © 2008 Victor Company of Japan, Limited