COLOR VIDEO MONITOR TM-1011G INSTRUCTIONS LCT1989-001A-H En_TM-1011_Cover.p65 1 06.2.
Thank you for purchasing this JVC Color Video Monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor’s capabilities. SAFETY PRECAUTIONS In order to prevent any fatal accidents caused by misoperation or mishandling of the monitor, be fully aware of all the following precautions. WARNINGS To prevent fire or shock hazard, do not expose this monitor to rain or moisture. Dangerous high voltages are present inside the unit.
POWER CONNECTION The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada only) and AC 220-240 V (For European countries or United Kingdom), the power cord attached conforms to the following power supply voltage and countries. Use only the power cord designated to ensure Safety and EMC regulations of each countries. Power cord Power supply voltage: Countries: AC 120 V U.S.A.
Controls and Features 7 Front Panel 1 2 3 4 5 1 Tally lamp ☞ “How to Use the MAKE/TRIGGER Terminal” on pages 14 and 15 • You can set the lamp color to red or green. ☞ “TALLY SELECT” on page 12 )/PHASE ( ) button Activates the Chroma (picture color density) adjustment mode or the Phase (picture hue) adjustment mode. Each time you press the button, the adjustment modes change. To adjust the value, move the MENU/VOLUME control (4) to / .
UNDER SCAN button Reduces the screen size so that the whole screen is displayed. 6 BLUE CHECK button Displays the blue video signal only. 7 COLOR OFF button Displays the luminance signal only. 8 INPUT SELECT buttons/lamps Select an input to display. A: Select the video and audio signals input to the VIDEO A and AUDIO A terminals. B: Select the video and audio signals input to the VIDEO B and AUDIO B terminals. • The corresponding lamp of the input currently selected lights up.
Controls and Features (cont.) 7 Rear Panel w r e t y u w Power input connectors You can use either AC or DC power supply to operate the monitor. AC IN: Connect to an AC outlet with the provided AC power cord. (AC 120 V/ 220-240 V, 50 Hz/60Hz). DC IN 12 V: Connect the power cord from the DC power supply (12 V). Pin terminals of the DC IN 12 V connector: 1 2 4 3 NOTES: • Regarding the DC power supply, consult with your dealer. • While connecting both the AC and DC power supply...
e AC power switch u DC switch Turns the AC power on and off. • I : on 䡬 : off Turns the DC power on and off. • I : on 䡬 : off NOTE: • You need to turn on the stand-by button on the front panel to turn on the monitor after turning on the AC power switch. NOTES: • You need to turn on the stand-by button on the front panel to turn on the monitor after turning on the DC switch. • The monitor consumes the battery even while the monitor is on stand-by.
Basic Menu Operations 7About the Menu Screens This monitor features MAIN MENU which contains the functions normally used and SET-UP MENU which contains the initial settings of the monitor. MAIN MENU Items Functions APERTURE CONTROL Compensates the frequency characteristics of the luminance signal of a video signal. sub menu SELECT Selects the positions and the contents of the sub-menu display. ASPECT Selects the aspect ratio.
7Displaying the Menu Screens 7About “ sub menu” To display MAIN MENU Push in the MENU/VOLUME control on the front panel. When “ sub menu” is displayed in the menu, only selected item in that menu can be displayed and adjusted. This allows you to make adjustments while looking at the actual screen. To display SET-UP MENU Push in the CHROMA/PHASE button while moving the MENU/VOLUME control to . NOTES: • To exit the menu, push in the MENU/VOLUME control several times.
How to Use MAIN MENU 7MAIN MENU Screens MAIN MENU Move the MENU/ VOLUME control to Setting Items . Move the MENU/ VOLUME control to / to adjust an item. About “ sub menu” and “reset,” ☞ page 9 ☞ page 9 ☞ see below. * To go back to the previous menu, press the MENU/VOLUME control. NOTE: • Some items do not appear on the menu depending on the signal currently input or if there is no signal input. Those items are not available to use.
How to Use SET-UP MENU 7SET-UP MENU Screens SET-UP MENU Move the MENU/ VOLUME control to Setting Items . ☞ page 13 Move the MENU/ / VOLUME control to to adjust an item. About “ sub menu” and “reset,” ☞ page 9 * To go back to the previous menu, press the MENU/VOLUME control. NOTE: • Some items do not appear on the menu depending on the signal currently input or if there is no signal input. Those items are not available to use. 11 En_11-20_TM-1011G.p65 11 06.2.
How to Use SET-UP MENU (cont.) 7Functions and Adjustment Range of Items FUNCTION SETTING Sets the control systems for the COLOR SYSTEM, colors of the tally lamp, and MAKE/TRIGGER terminal. • Can be also used to check the amount of time that the monitor has been used. 7 COLOR SYSTEM Selects the color system. AUTO: Changes NTSC and PAL automatically. NTSC: Keeps the color system NTSC. PAL: Keeps the color system PAL. 7 HOUR METER X100h Displays the total usage time of the monitor in hundred-hour units.
7 BLUE CUTOFF Adjusts the blue cut-off point. • MIN O MAX (in 155 grades) 7 RED CUTOFF Adjusts the red cut-off point. • MIN O MAX (in 155 grades) SIZE/POSI. ADJ. Adjusts the size and position of the picture. 7 TRAPEZOID Compensates the trapezoid picture distortion. • –20 O 00 O +20 –: Enlarges the upper side of the picture. +: Reduces the upper side of the picture. 7 ROTATION Compensates a picture tilt. • –31 O 00 O +31 –: Turns the picture clockwise. +: Turns the picture counterclockwise.
How to Use the External Control 7About the External Control The Monitor has the MAKE/TRIGGER terminal, which allows you to control the monitor by the MAKE (make contact) or TRIG. (trigger) system selected in the function setting. MAKE (make contact) system: Controls the function by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it. TRIG.
Functions controlled by the MAKE/TRIGGER Terminal Display INP. A INP. B CO. OFF ASPECT TALLY TA. SEL STATUS Functions to be controlled Changes the input to INPUT A Changes the input to INPUT B Turns on/off COLOR OFF Changes ASPECT Controls the tally lamp Selects the color of the tally lamp Turns on/off the status display Opening Invalid Invalid Off 4:3 Off Green Off Short-circuiting Valid Valid On (Monochrome screen) 16:9 On Red On *1 *2 *3 *1 The TRIG.
Troubleshooting Solutions to common problems related to your monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance. Problems No power supply No picture with the power on Points to be checked Measures (Remedy) Is the AC or DC power plug loose or disconnected? Firmly insert the power plug.
Measures (Remedy) Reference pages Adjust the picture size (H. SIZE, V. SIZE) or position (H. POSITION, V. POSITION) in “SIZE/ POSI. ADJ.” Adjust the picture distortion (PARALLELOGRAM, TRAPEZOID) or tilt (ROTATION) in “DISTORTION ADJ.” It may not be possible to expand the picture due to the selected input mode. In this case, adjustment is impossible. 13 Has the UNDER SCAN button been pressed? Press the UNDER SCAN button to remove the setting.
Specifications Model Type Picture Tube Effective Screen Size Scanning Frequency Video Band Horizontal Resolution Input/Output Terminals Audio output Speaker Compliant Video Signal Environmental Conditions Power Requirements Power Consumption Dimensions Weight Accessory TM-1011G Color Video Monitor 10" measured diagonally Width: 176.9 mm (6 15/16") Height: 137.6 mm (5 3/8") Diagonal: 224.
7Dimensions Unit : mm (inch) Front View Side View 164 (6 1/2") 338.3 (13 3/8") 307.8 (12 1/8") 229 (9 1/8") 1.5 (1/16") 220 (8 3/4") 183 (7 1/4")* 140 (5 5/8")* 222 (8 3/4") 7 (3/8") 63.5 (2 1/2") 222 (8 3/4") 7 (3/8") Asterisks (*) are used to indicate front panel dimensions. 19 En_11-20_TM-1011G.p65 19 06.2.
TM-1011G COLOR VIDEO MONITOR © 2006 Victor Company of Japan, Limited En_11-20_TM-1011G.p65 20 0306STH-MW-MT 06.2.
