TK-C205VP For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. VICTOR COMPANY OF JAPAN, LIMITED Model No. ® is a registered trademark owned by VICTOR COMPANY OF JAPAN, LTD. is a registered trademark in Japan, the U.S.A., the U.K. and many other countries. © 2004 VICTOR COMPANY OF JAPAN, LIMITED INSTRUCTIONS MANUEL D’INSTRUCTIONS INSTRUCCIONES TK-C205VP ® Printed in Thailand LWT0153 Serial No.
These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances. 15. Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the appliance. IMPORTANT SAFEGUARDS 16. Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards.
FOR USA AND CANADA INFORMATION (FOR CANADA) RENSEIGNEMENT (POUR CANADA) CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Features The unit can be installed directly outdoors since the dust/drip-proof structure (IP66) is unaffected by rain. The unit including the dome cover is designed for outdoor and indoor areas that are subject to vandalism. The camera uses a high-resolution 380,000 pixel (U type) / 440,000 pixel (E type), high-sensitivity CCD to realize high picture quality with horizontal resolution of 535 TV lines and S/N50dB. Dome-type design allows application in various locations.
Names and Operations of Parts Camera unit 3 MONITOR terminal (RCA pin) For connecting a monitor when determining camera angle, etc. (High impedance) 4 Horizontal lock screw When adjusting the camera angles of horizontal rotation, this screw is loosened for adjustment and tightened to maintain the angle. ( page 14) 5 Tilt lock screws During adjustment of the vertical image pickup direction of the camera angle, loosen the screws (2 locations) and retighten after performing adjustment.
Names and Operations of Parts Installation and connection Main unit bottom/side/top System diagram side top Camera 1 Video signal English bottom Power Camera 2 Video signal Power 121mm (43/4") Camera 3 Video signal Power MONITOR Camera 4 DVR, etc. Video signal SR-L910E REC STOP/EJECT REVERSE REW 1 Safety cable installation screw Install the safety cable using this screw. CAUTION Be sure to attach the safety cable. If not attached, the camera body could drop down.
Installation and connection Remove the camera unit from the base and mount the base to the pipe. • Do not remove the protective sheet affixed to the dome cover until installation work is completed. Removing the sheet during installation may result in scratching of the dome cover. Wrench 1. 1. Dome cover Base 2. 2. Remove the dome cover from the base Loosen the Tamper-resistant screws fixing the dome cover (3 locations) by using the provided wrench and turning counterclockwise.
Connect the Cables to the Base Video signal cables Connect the coaxial cables to the coaxial cable processing terminal. Note Use the RG-59 or RG-6 video signal cable (coaxial cable). The RG-11 cannot be used. • Perform the process shown on the left diagram (above illustration) for the coaxial cable tip before connecting. DC 12 V or AC 24 V power supply cable Connect a DC 12V or AC 24V power supply cable to the power supply terminal.
Installation and connection Adjusting the Camera Angle Attach the Dome cover Horizontal Lock screw Variable range 350˚ The dome cover is mounted on the base. Horizontal rotation (adjustable range: 350°) 1. Loosen the horizontal LOCK screw. 2. Holding the both tilt lock screws, rotate horizontally. LENS CENTER FOCUS ADJ. Switch Vertical rotation (adjustable range: +80°, -50°) 1. Loosen the tilt lock screws. 2. Holding the rotation levers, rotate 3. Tighten the tilt lock screws.
Installation and connection When installation cannot be made to the ceiling, use the conduit hole on the main unit side to install to the pipe. 1. Follow steps 1 ~ 5 of Mounting the Base to the Ceiling. 2. ( page 10 & 11) 2. Set screw Loosen the set screws (M3 × 6mm) with a flat-head screwdriver and remove the plug on the main unit side. When installation cannot be made using the conduit holes, install the dome camera to the electrical box. 4 Inch squara electrical box Mounting holes 1.
Others SPECIFICATIONS As a general characteristic unique to CCD, white spots may appear on the screen when operating under high temperature. In order to reduce this phenomenon, this unit is equipped with a white-spot correction feature. FOCUS ADJ. OFF OFF OFF AUTO LL PHASE R SPOT CORRECTION ON ON-AGC ON-BLC MANU INT WHT.BAL. Usage 1. Remove the dome cover. • Switch on the camera power supply and wait for at least 30 minutes. 2. Cover the lens surface using a black sheet of paper, etc.
Cut the wires Base Cap Wires Cut English Note when installing Italiano Note per The base of l’installazione this unit is noninsulated with the internal board grounding. When installing this unit to the conduit, always cut off the wires (2 pieces) as shown in the diagram above. Influence from devices that easily emit noise (power pumps, air conditioners, lighting, etc.) and dielectric effects from lightning can be reduced by insulating the base.
