COMBINATION CAMERA TK-C675B INSTRUCTIONS E EAS REL CK LO For Customer Use : Enter below the Serial No. which is located on the body. Retain this information for future reference. This instruction book is made from 100% recycled paper. Model No. TK-C675B Serial No.
For USA and CANADA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Operating precautions ● To save energy, when it is not being used turn the system's power off. ● This camera has been designed for indoor use. It cannot be used outdoors. ● This camera has been designed exclusively to be hung from the ceiling.It may malfunction if it is placed on a surface or if it is tilted. ● Do not install or use the camera in the following places. • In a place exposed to rain or moisture. • In a place with vapor or oil soot, for example in a kitchen.
Controls, connectors and indicators ■ Ceiling mount ■ Camera body 10 3 2 13 12 1 11 15 14 9 (Front) 8 Dome cover lens 4 Dome cover 5 6 16 7 5 17 Camera position alignment mark (Back: Camera side) View when the camera body cover 15 is removed 1 VIDEO OUTPUT terminal Outputs composite video signals and is to be connected to a monitor, etc. (Output impedance 75ohm) 2 Control signal terminals The camera can be controlled by RS-422A or RS-485 signals.
Installation 1. 1. Make a hole (90 mm dia.) in the ceiling for passing through the connection cables. ø90mm 2. Connect the cables to the terminal board. Remove the terminal board cover by flipping it up while pushing its top to the left. 2. TX+ TX– RX+ RX– VIDEO OUT To controller To monitor, etc.
Installation (continued) 4. Turn the camera body cover to anti clockwise to set the word 4. “RELEASE” on the camera body cover over the mark, then pull the camera body cover upward. Transportation bracket is mounted when it is shipped from the factory. Make sure to remove it before installation. 1 Remove the screw to remove the transportation bracket. 2 Then fasten the dome cover with the screw which was removed.
Installation (continued) 6. 6. Attach the camera body cover. Camera body cover Claw Align "RELEASE on the camera body cover with the indication mark on the camera body, fit the cover onto the camera body, then rotate the cover clockwise until “LOCK” is indicated. • Check that the three claws on the cover are locked onto the camera body and that there is no clearance between the cover and the camera body. Claw CK LO ASE RELE 7. Attaching the drop prevention wire.
Connections CAUTION If this camera and the cables connected to this camera is used where there are strong electromagnetic waves or where there is magnetism present, for example near a radio or TV transmitter, power transformer or an electric motor, the picture may produce noise and the colors may be affected. Optional controller is required to use the TK-C675B camera. Please contact your local dealer or installer for more information about this controller.
Connections (continued) ■ control signal connection Use a twisted-pair cable for the connection. ●Duplex When the camera is controlled with the full duplex protocol, set SW5 to OFF. ●Simplex When the camera is controlled with the simplex transmission protocol, set SW5 to ON. Camera RX+ Controller TX+ Camera RX+ Controller TX+ RX– TX– RX– TX– TX+ RX+ TX– RX– Two wires must be connected. Four wires must be connected.
Menu settings This chapter shows an example of connection to the JVC’s remote control unit RM-P2580. Read it and refer also to the instruction manual of the RM-P2580. Menu operations It is possible to set the menu screen of the remote control unit (RM-P2580).
Menu settings (continued) Menu screen flow The menu screen flow is as follows. For details, see the reference pages. Normal screen Camera SETUP screen SE TUP C AM E R A MOD E S E L E C T . . C AM E R A V I D E O A D J U S T . . V I DEO AD J F OR POS I . . T EX T ED I T . . A UTO PAN SE T . . A UTO P A T RO L SE T . . F AC TORY S E T T I NGS . . CAMERA MODE SELECT screen C AM E R A MOD E S E L E C T V . PHASE 127 P OS . T E X T L O C . U P— L A UTO F L I P OF F V AR .
Menu settings (continued) CAMERA MODE SELECT screen Item Variable range Function Factory setting V.PHASE Set when adjusting the vertical of other cameras operating in the line lock (LL) mode. Adjust while viewing the screen. The value will become smaller when the pan/tilt lever is pressed to the left (8). The value will become larger when the pan/tilt lever is pressed to the right (t). 0 ~ 255 127 POSITION TEXT LOCATION Used to set the display position of position titles.
Menu settings (continued) CAMERA VIDEO ADJUST screen Item AGC MODE Variable range Function The maximum gain of the AGC (Automatic gain control) is set. This setting value becomes a maximum limit when the gain is automatically changed according to brightness. Set this to 20dB when there is little light on the subject. Factory setting OFF 12 dB 20 dB 12 dB 1/60 (1/50), 1/100 (1/60), 1/1000, 1/2000, 1/4000, 1/10000 ( ) is version E.
Menu settings (continued) VIDEO ADJUST FOR POSITION screen Variable range Item Function POSITION TEXT It is possible to set up to 16 characters to use as titles for set positions (max. 63) and home positions (max. 1). See the next page for details on settings Factory setting MEMO Always register positions before setting titles. Positions cannot be selected unless they have been registered. For details on registering positions, see the instruction manual of the used remote control.
Menu settings (continued) POSITION TEXT screen It is possible to set titles to positions (max. 63) and home positions (max. 1) using text of 16 characters or less. MEMO Always register positions before setting titles. Positions cannot be selected when they are not registered. To register positions, see the instruction manual of the used remote control unit. SPACE 1.
Menu settings (continued) CAMERA TEXT screen It is possible to set up to 16 characters to use as a title during camera selection.
Menu settings (continued) AREA TEXT screen The 360° panning angle (horizontal rotation) is divided into 16 sectors, allowing you to check the title in each area. When the camera is manually panned, the preset area designation is shown on the screen. It is possible to set titles of 16 characters or less to each area. To select whether to display the title or not is made in AREA TITLE.
Menu settings (continued) ALARM TEXT screen It is possible to set up to 12 characters to use as a title during alarm.
Menu settings (continued) AUTO PAN SET screen Auto pan is a feature which allows the camera to slowly move sideways automatically and is set per each camera. There are 3 AUTO PAN modes: RETURN that goes back and forth between two points, RIGHT that makes a right rotation and LEFT that makes a left rotation.
Menu settings (continued) AUTO PATROL SETUP screen The auto patrol is a feature to move the camera to multiple positions at high speed in a set sequence and time and is set per each camera.
Menu settings (continued) FACTORY SETTINGS screen It is possible to return all camera settings to the factory settings.
Troubleshooting Symptom Cause (Information) Remedy Video is not output. • Is there a problem in the power cables con-necting the camera to the power supply unit. (If the power cables are too long or are of the wrong size, the correct voltage may not be supplied due to an increase in resistance.) • Connect low resistance cables. • Place the AC 24V power supply near to the camera.
Specifications ■ CAMERA Image device : U type Based on NTSC standard E type Based on PAL standard Panning : 360 degree endless Tilting : 0 to 90 degrees : 1/3"IT CCD Panning speed : 240 degree/sec, 80 degree/sec, 60 degree/sec, 40 degree/sec, 20 degree/sec, 12 degree/sec, 6 degree/sec, 4 degree/sec, 2 degree/sec Effective picture : U type 380,000 pixels, 771 (H) × 492 (V) E type 440,000 pixels, 753 (H) × 582 (V) element Sync system : Line lock/Internal Video S/N : 48dB (Typ.
TK-C675B COMBINATION CAMERA VICTOR COMPANY OF JAPAN, LIMITED is a registered Trademark owned by VICTOR COMPANY OF JAPAN, LTD. is a registered Trademark in JAPAN, the U.S.A., the U.K. and many other countries.
