Manual

IMPORTANT:
lb optrrate JVC's vide_ components using the supplied remote
control:
• You need to connect JVC's vidtx_ tom.heats through the AV
COMPU LINK jacks (see page 42) in addition m the connections
using canes with RCA pin plugs (see pages 14 and 15),
• Seam JVC's VCRs can accept two types of the control aignais--
remote c{xte "._i' and '*B?' Before using this remote control, make
s_re that the remote control code of the 'targetVCR is s_t to c{xte
,%?,
-For RX-8030VBK: When another JVC's VCR is connected to
the VCR 2 or VIDEO terminals, set iIs remote coning c{_e to
c{_c "B?' (l'his remote control cannot emiI the control signals of
cc_e "BY)
• When using the remote control, aim the remote control diractly at
the remote sensor on each component, not on the receiver,
For RXJ!O3OVBK:
V_rhan you press one of the sou£rce selection
buttons, the operation mode appe_'s on the
display window.
Butlons Indications
VCR 1 VCR 1
DVD or DVD MUI3'I DVD
TV/I_BS TV
VCR [ _ TAPE
CONTROL repeatedly)* _ CDDSC "- CDR
* By pressing CONTROL repeatedly, you con select
"VCR 1," _7-APE," _C,DR _or _DDSC" as the _uree.
When you Wcss one of the buttons listed above, the
remote operation mode appears on the operation mode
di@ay t'{yrabout two hours.
vcR
You can always poffoml the following operations:
VCR 1 O11(for RX-8030VBK) or VCR O11(for RX-7030VBK/RX-
7032VSL): 3_Irn on or off a VCR.
For RX-P-_13OVBK: A:ffer pressing VCR 1 (,,_"selecting _'VCR l"
by pressing CObrI'ROL repeatedly), you can porfoml the following
operations on aVCR:
For RX-7030VBK/RX-7032VSL: A:ffor pressing VCR _o'_"VCR
CObrI'ROL), you can porforrathe following operations on aVCR:
1 -9,0:
REW:
FF:
I1:
t1:
REC PAUSE:
CH +/-:
Select the TV channels on a VCIL
Start playing.
Rewind a tape+
F_st wind a tape,
Stop playing or recor_Ymg,
Pau_ playing, lb resunt_, press I_,
Entor reco_mg pause by pressing this button,
lb st*m recording again, press this button than I_.
Change the TV channels on the VCIL
Note:
You con use either VCR 1 (for RX_803OVBK) or VCR (for RX-
7030VBK/RX-7032VSL) or the control button (CONTROL for RX-
8030VBK or VCR CONTROL for RX-ZO30VBK/RX-ZO32VSL) to
activate the buttons listed above. If you press one of the source
selection buttons, the playing sou_ also changes. On the other
hand, pressing the control button does not change the playing source.
After pressing D¥33 or DVD Mldl21'I, you can perfc_ml the
following operations on a DVD player:
1,-: Start playing,
I.._-,,1: Remm to the beginning of the c_zrent (or Wevious) chapter,
I_l_: Skip to the beginning of the next chapter,
m: Stop Naying,
t1: Pause playing, lb resume, Fress I_,
After pressing DVD cq DYq) MUEI%
these buttons can be used f{yrthe DVD
menu operations.
T_7
Note: @I
For detailed menu operation_, referto the
instructions supplied with the discs or the
DVDplayer.
0--
You can always perform the following opera_ons:
TV O/1: 311rnon or offthe T'vl
TV VOL +/-: Adjt_st the volume,
TV_IDEO: Set the input m(_e (either I'V or V1DEO),
After prssaing TWDBS, you can pcrfc_ma the following operations
on a TV:
OH +/-: Change the channels,
1 - 9, 0, 100+: Select the channels.
RETURN: Alternate between the Freviously selected chananl
andthe c_rrent channel,
46