Manual

BassReinf°rcingthe _!
Using the Sleep
Timer
Mutingthe
Sound
Changing
the Display
Brightness
Using the Sleep Timer, you can fall asleep while listening to music.
When the shut-off time comes, the receiver turns off aWomatically.
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and the shut-off time
changes in 10 minutes inlervals:
F IO .-- 20 .-- 30 .-- 40.-- 50 .-,-60 .-- 70 .-- 80 .-- 90 --I/
0 (Canceled) , /
To check or change the time remaining until the shut-off time:
Press SLEEP once.
The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly until "SLEEP 0rain" appears on the display.
(The SLEEP indicalor goes off.)
• "Fuming off the power also cancels Ihe Sleep Timer.
Iff_llll_.I_ _ I=!_L'_
You can boost the bass level.
• Once you have made adjustment, it is memorized for each source.
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2. Press BASS BOOST to turn on Bass Boost.
The BASS BOOST indicator lights up.
• Each time you press the button, Bass Boost turns on ("BOOST
ON") and off ("BOOST OFF") a[lernate[y.
For RX-7030VBK/RX-7032VSL:
You can use the BASS BOOST button on 1he front panel.
When the Bass Boost is activated, the lamp on the button lights up.
• Each time you press the button, Bass Boost turns on and off.
Notes:
• This function affects only the sounds from the front speakers,
center speaker, and subwoofe_
• When Analog Direct is in use (see page 21), the Bass Boost is
canceled temporarily,
hY!I!l_ It I'_ l-'ftl'_, I
Press MUTING to mute the sound through all speakers and
headphones connected.
"MUTING" appears an the display and the volume turns oft"(the
VOLUME [eve[ indicator goes off).
To restore the sound, press MUTING again.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +1- on the remote control also reslores the sound.
You can dim the display.
Press DIMMER.
• Each time you press the button, the brightness
level of the display change as follows:
_Dimmer -_ Much dimmer
Canceled , /
(Normal display)
22
Recording a source
For analog-to-analog recording
You can record any analog playback source onto the recording
components connected to the audio owput jacks on the rein"of
this unit at the same time.
For digital-to-digital recording
You can record the currently selected digital input source through
the receiver to a digital recording device connected to the
DIGITAL OUT lerminah
Notes:
i
• Analog-to-digital and digital-to-analog recordings are not
possible,
• The output volume level, Midnight Mode (see page 20), Bass
Boost (see the left column), Digital Equalization (see page 32),
Surround modes and DSP modes (see pages 34 to 39) cannot
affect the recording.
Basic adjustment auto memory
This receiver memorizes sound settings for each source-
* when you turn off the power,
• when you change the source, and
• when you assign 1he source name (see page 21),
When you change the source, the memorized settings for the
newly selecled source are automatically recalled.
The following can be stored for each source:
Analog/digital input mode (see pages 19 and 20)
Input anenuator mode (see page 20)
Analog Direct (see page 21)
Digital Equalizalion (see page 32)
Speaker channel output levels (see page 32)
Sun'ound and DSP mode selection (see pages 37 and 39)
Bass Boost seuing (see the left column)
Notes:
i
• If the source is FM or AM, you can assign a different setting for
each band,
• If you want to memorize the volume level with the above
settings, set One Touch Operation to "ON" (see page 30).