LT-Z32/26S2 (ASIA) / LCT1597-001A / All cover LCT1597-001A_Cover.
LT-Z32/26S2 (ASIA) / LCT1597-001A / All cover LCT1597-001A_Cover.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 1 Thursday, December 18, 2003 10:11 AM Thank you for buying this JVC LCD flat television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. (“LCD” stands for Liquid Crystal Display.) WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING Always use the power cord which is supplied with the TV.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 2 Thursday, December 18, 2003 10:11 AM Point defects LCDs use collections of fine pixels to display images. While there is no problem with more than 99.99% of these pixels, please understand that a very small number of pixels may not light or may light all the time. Distance recommendations ENGLISH Avoid improper installation and never position the unit where good ventilation is impossible.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 3 Thursday, December 18, 2003 10:11 AM CONTENTS Setting up your TV..................................4 SOUND SETTING ................................. 21 Installation..........................................................4 Using the stand ..................................................4 Putting the batteries into the Remote control.....5 Remove the terminal covers ..............................5 Connecting the aerial and VCR .....
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 4 Thursday, December 18, 2003 10:11 AM Setting up your TV • When you install the TV on the wall, only use a JVC wall mounting unit (optional) which is designed for this TV. • Ensure that the TV is installed on the wall by a skilled installer. Installation Cautions for installation • Install the TV in a corner on a wall or on the floor so as to keep cords out of the way. • The TV will generate a slight amount of heat during operation.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 5 Thursday, December 18, 2003 10:11 AM Setting up your TV Putting the batteries into the Remote control Use two AA/R6 dry cell batteries. Insert the batteries from the - end, making sure the + and - polarities are correct. Follow the warnings printed on the batteries. Battery life is about six months to one year, depending on your frequency of use.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 6 Thursday, December 18, 2003 10:11 AM Setting up your TV Connecting the aerial and VCR • Aerial cable is not supplied. Use a good quality 75-ohm coaxial cable. • Read the manual that came with the VCR before connecting. If not connecting a VCR (follow 1): Connect an aerial cable to the aerial socket on this TV.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 7 Thursday, December 18, 2003 10:11 AM Initial settings When the TV is first turned on, it enters the initial setting mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to make the initial settings. VCR/TV/DVD Switch 3 Press the a button The LANGUAGE menu appears. LANGUAGE BACK TV OK D0002(E)-EN 4 Press the 5 and 6 buttons to choose ENGLISH.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 8 Thursday, December 18, 2003 10:11 AM Initial settings 6 Press the blue button to start the AUTO PROGRAM function The AUTO PROGRAM menu appears and received TV channels are automatically registered in the Programme numbers (PR). • To cancel the AUTO PROGRAM function: Press the b button.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 9 Thursday, December 18, 2003 10:11 AM TV buttons and functions 1 Turn the TV on from standby mode Press the A button or P p buttons to turn the TV on from standby mode When the TV is turned on, the power lamp dims slightly. • Check that the AC plug on the power cord from the TV is connected to correctly AC outlet.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 11 Thursday, December 18, 2003 10:11 AM Remote control buttons and functions Use the PR LIST: 1 Press the h (Information) button to display the PR LIST Pressing the h (Information) button changes the display as follows: ID 12 : 00 TV VIDEO modes Programme numbers PR 1 – PR 99 or +10 D0011-EN 2 Press the 5 and 6 buttons to choose a Programme number (PR).
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 12 Thursday, December 18, 2003 10:11 AM Remote control buttons and functions ZOOM function You can change the screen size according to the picture aspect ratio. Choose the optimum one from the following ZOOM modes.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 13 Thursday, December 18, 2003 10:11 AM Remote control buttons and functions Displaying the current time Using the PIP function You can display the Current Time on the screen. Press the h (Information) button to display the current time Pressing the h (Information) button changes the display as follows: You can view two pictures (Main-picture and sub-picture).
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 14 Thursday, December 18, 2003 10:11 AM Remote control buttons and functions Cancelling the PIP function: Press the R button or b button. ENGLISH • If the main-picture signal is poor, the quality of the sub-picture may also be poor. • If the pictures have different standards, the top and bottom of one of them may be missing. • If an external device is operated, the sub-picture may disappear.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 15 Thursday, December 18, 2003 10:11 AM Teletext function Basic operation Using the List Mode 1 Choose a TV channel with a teletext broadcast 2 Make sure to set the VCR/TV/DVD switch to the TV position. You can store the numbers of your favourite teletext pages in memory and call them up quickly using the colour buttons.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 16 Thursday, December 18, 2003 10:11 AM Teletext function Sub-page Some teletext pages include sub-pages that are automatically displayed. 1 Choose a teletext page that includes sub-pages Sub-page numbers that can be viewed are automatically displayed at the top of the screen. ENGLISH 2 Press the 5 buttons to choose a sub-page number Reveal Some teletext pages include hidden text (such as answers to a quiz).
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 17 Thursday, December 18, 2003 10:11 AM Using the TV’s menu This TV has a number of functions you can operate using menus. To fully utilize all your TV’s functions, you need to understand the basic menu operating techniques fully. 3 Press the 6 buttons to choose a function • For details of the functions in the menus, see the following pages. 5 Press the a button to complete the setting The menu disappears.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 18 Thursday, December 18, 2003 10:11 AM PICTURE SETTING Refer to “Using the TV’s menu” (see page 17) for details of displaying the menu. PICTURE SETTING PICTURE MODE BRIGHT-1 CONTRAST BRIGHT-2 SHARP COLOUR TINT WHITE BALANCE BRIGHT MID BACK TV RESET OK D0014-EN ENGLISH PICTURE MODE You can choose one of three PICTURE MODEs to adjust the picture settings automatically. BRIGHT: Heightens contrast and sharpness.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 19 Thursday, December 18, 2003 10:11 AM PICTURE FEATURES Refer to “Using the TV’s menu” (see page 17) for details of displaying the menu. PICTURE FEATURES DIGITAL VNR Super DigiPure COLOUR SYSTEM PULL DOWN 4:3 AUTO ASPECT COLOUR MANAGEMENT PIP AUTO AUTO AUTO ON BACK TV OK D1015-EN The DIGITAL VNR function cuts down the amount of noise in the original picture.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 20 Thursday, December 18, 2003 10:11 AM PICTURE FEATURES COLOUR SYSTEM PULL DOWN The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually. 1 Choose COLOUR SYSTEM. Then press the a button The sub-menu of the COLOUR SYSTEM function appears.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 21 Thursday, December 18, 2003 10:11 AM SOUND SETTING Refer to “Using the TV’s menu” (see page 17) for details of displaying the menu. You can turn off the sound from the TV speakers; but you should only do this if an audio system is connected to the TV as a substitute for the TV speakers. SOUND SETTING STEREO/ BASS TREBLE BALANCE SPEAKER BBE CINEMA SURROUND A.H.B.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 22 Thursday, December 18, 2003 10:11 AM SOUND SETTING HEADPHONE You need to use the HEADPHONE menu to adjust the volume of the headphones. The HEADPHONE menu can also be used to set whether or not sound comes from the TV speakers when the headphones are being used and to perform the settings for the sound coming from the headphones. ENGLISH 1 Press the 6 buttons to choose HEADPHONE.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 23 Thursday, December 18, 2003 10:11 AM FEATURES Refer to “Using the TV’s menu” (see page 17) for details of displaying the menu. FEATURES SLEEP TIMER BLUE BACK CHANNEL GUARD OFF ON To set the CHANNEL GUARD function 1 Choose CHANNEL GUARD, then press the o button “SET ID NO.” (ID number setting screen) appears. SET ID NO.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 24 Thursday, December 18, 2003 10:11 AM FEATURES 3 Press the Number buttons to enter the ID number The lock is temporarily released so you can view the TV channel. If you have forgotten the ID number: Perform step 1 of “To set the CHANNEL GUARD function”. After confirming the ID number, press the b button to exit the menu.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 25 Thursday, December 18, 2003 10:11 AM INSTALL Refer to “Using the TV’s menu” (see page 17) for details of displaying the menu. INSTALL LANGUAGE AUTO PROGRAM EDIT / MANUAL BACK TV OK 3 Press the a button to start the AUTO PROGRAM function The AUTO PROGRAM menu appears and received TV channels are automatically registered in the Programme numbers (PR). • To cancel the AUTO PROGRAM function, press the b button.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 26 Thursday, December 18, 2003 10:11 AM INSTALL 2 Follow the operation description of a function you want to use and operate the function 2 Press the red button to start the ID function EDIT MOVE: This function changes a Programme number (PR) of a TV channel. ID: This function registers a Channel name (ID) to a TV channel.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 27 Thursday, December 18, 2003 10:11 AM INSTALL 4 Press the Number buttons to enter the remaining CH/CC number The TV shifts to registration mode. When the registration is completed, the picture of the TV channel appears on the screen. • The CH/CC number is a number indicating the broadcast frequency to the TV.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 28 Thursday, December 18, 2003 10:11 AM INSTALL Changing the TELETEXT LANGUAGE setting After the AUTO PROGRAM function is completed, you can change the country you have already set by using the AUTO PROGRAM function. 1 Display the INSTALL menu ENGLISH When the EDIT menu is currently being displayed: Press the h (Information) to return to the INSTALL menu. 2 Press the 6 buttons to choose AUTO PROGRAM.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English Body_Eng.fm Page 29 Thursday, December 18, 2003 11:09 AM Additional preparation Connecting the external devices Connect the devices to the TV, paying attention to the following connection diagram. Before connecting anything: • Read the manuals provided with the devices. Depending on the devices, the connection method may differ from the figure. In addition, the device settings may be changed depending on the connection method to secure proper operation.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 30 Thursday, December 18, 2003 10:11 AM Additional preparation Connecting devices to the OUT terminal The signals of the images and sound you are currently viewing with this TV are output through the OUT terminal. By connecting a VCR to the OUT terminal, you can record the currently shown image and sound to that VCR. To do this, connect the VCR and OUT terminal following the steps below.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 31 Thursday, December 18, 2003 10:11 AM CH/CC numbers When you want to use the INSERT function on page 26, find the CH/CC number corresponding to the Channel number of the TV channel from this table. US: The US channel numbers are the channel numbers used in the United States, Philippines, etc. CCIR: The CCIR channel numbers are the channel numbers used in the Middle East, Southeast Asia, etc.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 32 Thursday, December 18, 2003 10:11 AM Troubleshooting If a problem arises while you are using the TV, please read this “Troubleshooting” well before you request having the TV repaired. You may be able to fix it easily by yourself. For example, if the AC plug is disconnected from the AC outlet, or the TV aerial has problems, you may think there is a problem with the TV itself.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 33 Thursday, December 18, 2003 10:11 AM Troubleshooting Other concerns ENGLISH • When the SLEEP TIMER function operates, the TV is automatically turned off. If the TV is turned off suddenly, try to press the # (Standby) button to turn on the TV once again. At this time, if the TV resumes a normal state, there is no problem.
LT-Z32/26S2 (ASIA) / LCT1597-001A / English LT-Z32&26S2_Eng.book Page 34 Thursday, December 18, 2003 10:11 AM Specifications Item Model LT-Z32S2 LT-Z26S2 Broadcasting systems B, G, I, D, K, K1, M Colour systems PAL, SECAM, NTSC 3.58/4.43 MHz Channels and frequencies VHF low channel (VL) =46.25 to 168.25 MHz VHF high channel (VH) =175.25 to 463.25 MHz UHF channel (U) =471.25 to 855.
LT-Z32/26S2 (ASIA) / LCT1597-001A / All cover LCT1597-001A_Cover.
LT-Z32/26S2 (ASIA) / LCT1597-001A / All cover LCT1597-001A_Cover.
LT-Z32/26S2 (ASIA) / LCT1597-001A / All cover LCT1597-001A_Cover.
LT-Z32/26S2 (ASIA) / LCT1597-001A / All cover LCT1597-001A_Cover.
