Owner's Manual
Table Of Contents
- Instruction Manual
- Software License Agreement
- Important Notice concerning the Software
- Contents
- Before Use
- Basics
- Getting Started
- HD Radio™ Tuner (for KD-X470BHS)
- Radio (for KD-X370BTS/KD-X37MBS/KD-X270BT/KD-SX26BT)
- USB/iPod
- AUX
- Pandora®
- Spotify
- SiriusXM® Radio (for KD-X470BHS/KD-X370BTS/KD-X37MBS)
- Using Other Applications
- Bluetooth®
- AMAZON ALEXA (for KD-X470BHS/KD-X370BTS/KD-X37MBS)
- Audio Settings
- Display Settings
- References
- Troubleshooting
- Installation/Connection
- Specifications
- Quick Start Guide
- When it is not required to detach the front control panel from the main unit, use the provided screw to attach the control panel to the main unit.
- Warranty
ENGLISH
43
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Troubleshooting
Symptom Remedy
Bluetooth®
“H/W ERROR” Reset the unit and try the operation again. If “H/W ERROR”
appears again, consult your nearest service center.
“SWITCHING NG” The connected phones might not support phone switching
feature.
The Bluetooth connection
between the Bluetooth
device and the unit is
unstable.
Delete the unused registered Bluetooth device from the
unit. (Page 25)
AMAZON ALEXA
No response from Alexa
after the voice input.
Amazon cloud was unable to analyze the voice input.
Wrong response from
Alexa.
Alexa misunderstood what was said or did not catch
the entire request or sentence spoken. Please try again.
(Page 28, 29)
“DISCONNECTED” Be sure to connect your smartphone to the unit via
Bluetooth. (Page 21)
Not able to connect or
reconnect to Alexa mobile
application.
• Be sure the audio device is connected via Bluetooth. Select
the audio device from [AUDIO SELECT] in [BT MODE].
(Page 25)
• Perform the one-time setup process again. See “Setup for
the first time” on page 27.
• Turn off, then turn on the unit and try to connect again.
• For iOS device, make sure ALEXA source or iPod BT source
is selected.
If you have any troubles, try the following:
1 Check TROUBLESHOOTING
2 Reset the unit (page4)
3 Contact (USA only)
Call: 1-800-252-5722 ( or ) visit: <http://www.jvc.com>
This section is for the professional installer.
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
WARNING
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
• To prevent short circuit:
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires that come in contact
with metal parts to protect the wires.
CAUTION
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the
wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
• Connect speakers with a maximum power of more than 50 W. If the maximum power of the
speakers is lower than 50 W, change the [AMPGAIN] setting to avoid damaging the speakers.
(Page 30)
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on
and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
Installation/Connection
JS_JVC_KD_X470BHS_K_EN_3.indd 43JS_JVC_KD_X470BHS_K_EN_3.indd 43 6/21/2019 11:52:40 AM6/21/2019 11:52:40 AM