Owner's Manual

No
Bluetooth
device
•
Search
from
the
Bluetooth
device
again.
is
detected.
•
Reset
the
unit.{+
3)
f------
----
----
--
---
--
--
- -
---
·-·
-·-
----
-----
·
··--
--
·- -
---·
-
··
---
...
---
---------····
···
-;;-
-
.....
.
®
..r:::.
Pairing
cannot
be
made.
FULL"
appears.
"PLEASE
WAIT"
appears.
g
'~BT
DEVICE
NOT
-
~
FOUND"
appears.
Ci5
Echo
or
noise
occurs.
•
Make
sure
you
have
entered
the
same
PIN
code
to
both
the
unit
and
Bluetooth
device.
•
Delete
pairing
information
from
both
the
unit
and
the
Bluetooth
device,
then
perform
pairing
again.
{+13)
The
number
of
registered
devices
has
reached
its
limit.
Retry
after
deleting
an
unnecessary
device.
{+
17,
DELETE
PAIR)
The
unit
is
preparing
to
use
the
Bluetooth
function.
If
the
message
does
not-disappear,
turn
off
and
turn
on
the
unit,
then
connect
the
device
again.
The
unit
failed
to
search
for
the
registered
Bluetooth
devices
during
[AUTO
CNNG].
Turn
on
Bluetooth
from
your
device
and
connect
manually.
(+
17)
······
··-······
········
······-··
·-··
···
·
··
-····
······-··-
•
Adjust
the
microphone
unit's
position.
(+13)
•
Check
the
[ECHO
CANCEL]
setting.
(+
15)
Phone
sound
quality
•
Reduce
the
distance
between
the
unit
and
the
Bluetooth
is
poor.
"NOT
SUPPORT"
appears.
"ERROR"
appears.
device.
•
Move
the
car
to
a
place
where
you
can
get
a
better
signal
reception.
·
The
connected
phone
does
not
support
Voice
Recognition
feature.
Try
the
operation
again.
If
"ERROR"
appears
again,
check
if
the
device
supports
the
function
you
have
tried.
----···
--
--
--
-
------
TROUBLESHOOTING
sym
.ptom
®
..r:::.
-
0
'
The
unit
does
not
respond
when
you
try
to
copy
the
phonebook
to
the
unit.
Sound
is
being
interrupted
or
skipped
during
playback
of
a
Bluetooth
audio
player.
You
may
have
tried
to
copy
the
same
entries
(as
5tored)
to
the
unit.
Press
DISP
or~
PTY
to
exit.
•
Reduce
the
distance
between
the
unit
and
the
Bluetooth
audio
player.
•
Turn
off,
then
turn
on
the
unit
and
try
to
connect
again.
•
Other
Bluetooth
devices
might
be
trying
to
connect
to
the
unit.
.S
'
The
connected
Bluetooth
•
Check
whether
the
connected
Bluetooth
audio
player
supports
AudioNideo
Remote
Control
Profile
,
(AVR(P}.
(Refer
to
the
instructions
of
your
audio
player.)
QJ
~
'
audio
player
cannot
be
controlled.
•
Disconnect
and
connect
the
Bluetooth
player
again.
--·
-·
-----
----~-
-------
--------
--
-
-
--
.--------
-------
---
--
·---
-
--
--~
--·-~
-
----
----
--- ---
--
---
--~-------
-~
--
--
---
"H/W
ERROR"
appears.
Reset
the
unit
and
try
the
operation
again.
If
"H/W
"BT
ERROR
PLS
UPDATE"
appears.
_
ERROR"
appears
again,
consult
your
nearest
service
center.
Update
the
Bluetooth
firmware.{+
4)
··
·
··
·
·····················
···
···············
··
······ ·············
············
·········
···
··
·
················•··•·····
··•
··
................
......
......
.
If
you
have
any
troubles,
try
the
following:
1 Check
TROUBLESHOOTING
2 Reset
the
unit(+
3)
3 Contact
(USA only)
Call: 1-800-252-5722
(or)
visit:
http://www.jvc.com
ENGLISH
I
25