Operation Manual

ENGLISH
23
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
KD-R899BT/KD-R891BT:
Setting on
[SPK/PRE OUT]
Audio signal through lineout terminal
FRONT REAR/SW
REAR/REAR Front speakers output Rear speakers output
REAR/SUB.W (default) Front speakers output Subwoofer output
SUB.W/SUB.W Front speakers output Subwoofer output
KD-R794BT/KD-R792BT:
Setting on
[SPK/PRE OUT]
Audio signal through lineout terminal
REAR/SW
REAR/REAR Rear speakers output
REAR/SUB.W (default) Subwoofer output
SUB.W/SUB.W Subwoofer output
Connection via speaker leads
For connections without using an external amplifier. However, with this
settings you can also enjoy the subwoofer output.
( 35)
Setting on
[SPK/PRE OUT]
Audio signal through rear speaker lead
L (left) R (right)
REAR/REAR Rear speakers output Rear speakers output
REAR/SUB.W Rear speakers output Rear speakers output
SUB.W/SUB.W Subwoofer output (Mute)
If [SUB.W/SUB.W] is selected:
–
[120HZ] is selected in [SUBWOOFER LPF] and [THROUGH] is not available.
( 24)
– [POSITION R02] is selected in [FADER] and selectable range is [POSITION
R15]
to [POSITION 00] . ( 21)
Crossover settings
Below are the available setting items for 2-way crossover and 3-way
crossover.
Caution
Select a crossover type according to how the speakers are connected.
( 35)
If you select a wrong type:
• The speakers may damage.
• The output sound level may be extremely high or low.
SPEAKER SIZE
Selects according to the connected speaker size for optimum
performance.
• The frequency and slope settings are automatically set for the crossover
of the selected speaker.
• When 2-way crossover is selected, if [NONE] is selected for [TWEETER] of
[FRONT] , [REAR] and [SUBWOOFER] for [SPEAKER SIZE] , the [X ‘ OVER] setting of
the selected speaker is not available.
• When 3-way crossover is selected, if [NONE] is selected for [WOOFER] of
[SPEAKER SIZE] , the [X ‘ OVER] setting of [WOOFER] is not available.
X ‘ OVER
(crossover)
• [FRQ] / [F-HPF FRQ] / [R-HPF FRQ] / [SW LPF FRQ] / [HPF FRQ] / [LPF FRQ] : Adjusts the
crossover frequency for the selected speakers (high pass filter or low
pass filter).
If
[THROUGH] is selected, all signals are sent to the selected speakers.
• [SLOPE] / [F-HPF SLOPE] / [R-HPF SLOPE] / [SW LPF SLOPE] / [HPF SLOPE] / [LPF SLOPE]:
Adjusts the crossover slope.
Selectable only if a setting other than
[THROUGH] is selected for the
crossover frequency.
• [SW LPF PHASE] / [PHASE]: Selects the phase of the speaker output to be in
line with the other speaker output.
•
[GAIN LEFT] / [GAIN RIGHT] / [F-HPF GAIN] / [R-HPF GAIN] / [SW LPF GAIN] / [GAIN] :
Adjusts the output volume of the selected speaker.
JS_JVC_KD_R992BT_E_EN_3.indd 23JS_JVC_KD_R992BT_E_EN_3.indd 23 7/27/2017 9:47:05 AM7/27/2017 9:47:05 AM