Owner's Manual

Installation
Befor
e
in
stallation of
thi
s unit, p
lease
note
th
e
fo
llo
w
ing
precaution
s.
..A.WARNINGS
If
you
connect the ignition
wire
(red)
to the negative
ground point,
you
may
cause
a short circuit, that
in
turn
may
start a
fire.
Always
connect
those
wires
to
the power
source
running through the
fuse
box.
Do
not cut out the
fuse
from
the ignition wire
(red).
The
power supply must
be
connected to the
wires
via
the
fuse.
~
NOTE
Mounting
and
wiring
this
product
requires
skills
and
experience.
For
best
safety,
leave
the mounting
and
wiring work to
professionals.
Make
sure
to ground the unit to a negative
12V
DC
power
supply.
Do
not
use
your own
screws.
Use
only the
screws
provided. If
you
use
the wrong
screws,
you
could
damage
the unit.
If your
vessel
ignition
does
not
have
an
ACC
position,
connect the ignition
wires
to a power
source
that
can
be
turned
on
and
off
with the ignition
key.
If
you
connect the ignition wire to a power
source
with a
constant voltage
supply,
such
as
with battery
wires,
the battery
may
be
drained.
If the
console
has
a
lid,
make
sure
to
install
the unit
so
that the front
panel
will not hit the
lid
when
closing
and
opening.
If the
fuse
blows,
first
make
sure
the
wires
aren't
touching to
cause
a short circuit, then
replace
the
old
fuse
with one with the
same
rating.
Insulate
unconnected
wires
with vinyl
tape
or other
similar
material.
To
prevent a short circuit,
do
not
remove
the
caps
on
the
ends
of the unconnected
wires
or the
terminals.
Secure
the
wires
with
cable
clamps
and
wrap
vinyl
tape
around
the
wires
that
comes
into contact with
metal
parts
to protect the
wires
and
to prevent short
circuit.
Connect the
speaker
wires
correctly
to
the terminals
to which they
correspond.
The
unit
may
be
damaged
or
fail
to work
if
you
share
the 8
wires
or
ground them to
any
metal
part
in
the
vessel.
When
only two
speakers
are
being connected to
the
system,
connect the connectors either
to
both
the front output
terminals
or to both the
rear
output
terminals
(do
not
mix
front
and
rear).
For
example,
if
you
connect the
EB
connector
of
the left
speaker
to
a front output terminal, do not connect the 8
connector to a
rear
output terminal.
After the unit
is
installed,
check
whether the
signal
lamps,
wipers,
etc.
on
the
vessel
are
working
properly.
Reception
may
drop if there
are
metal
objects
near
the Bluetooth
antenna
.
Bluetooth
antenna
unit
[j
Supplied accessories
for
installation
CD
t:J~
Cl)
~
xl
I
xl
®
~
©
~
xl
(M3.5
x
25
mm)
x4
®
®
~
(M4)
x8
(M4x
37
mm)
x2
(J)
®
xl
~
xl
[j
Installation procedure
1)
To
prevent a short circuit,
remove
the
key
from
the ignition
and
disconnect the 8 terminal of the
battery.
2)
Make
the proper input
and
output wire
connections for
each
unit.
3)
Connect the wire
on
the wiring
harness.
4)
Connect the wiring
harness
wires
in
the following
order;
ground, battery, ignition.
5)
Connect the wiring
harness
connector to the unit.
6)
Install
the unit in your
vessel.
7)
Reconnect
the 8 terminal
of
the
battery.
Engli
sh I 15