User Manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Monitor Speaker
- Adjusting Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- SD Card
- About the Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting a Recording Format
- Zoom Operation
- Focus Operation
- Adjusting the Focus by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Using the Histogram
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Connecting External Devices
- Managing/Editing Clips on a PC
- Connecting External Monitor
- Connecting a Earphone
- Connecting Wired Remote Control
- Connecting a Remote Control Unit
- Functions Operable from the Remote Control Unit
- Inputting SDI Signals from an External Device
- Inputting External Synchronizing Signals (Genlock)
- Displaying Return Videos from an External Device
- Studio System
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
User Switch Set Item
USER1 to USER11, Lens RET
By assigning one of the menu functions below to
the [OIS/1], [MARKER/2], [LOAD FILE/3],
[F.ASSIST/4], [J/5], [K/6], [7/H/ZEBRA], [8/I/
SPOT METER], [AWB/9], [REC/10], [AUTO
FOCUS/11] buttons and the [RET] button on the
lens, you can operate the preset function (on/off,
startup, switching).
Set according to the shooting conditions. Usable
only in the Camera mode.
The settable values for each item are as follows.
.
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
： −：
Settable
Setting Value
Item
Live Streaming
Load Picture File
Return VideoAB
Clip Review
OK Mark
Clip Cutter Trig
Backup Trig
Rec
LCD Backlight
Expanded Focus
Histogram
Spot Meter
Focus Assist
Marker
Zebra
AWB
White Balance
Preset Zoom1 to Preset Zoom3
Auto FocusF
One Push FocusF
One Push IrisF
OISF
Face DetectF
AE Lock
Lolux
Flash Band
Bars
None
Not settable
USER11
USER9, USER10
USER1 to USER8,
Lens RET
Lolux
To increase the sensitivity when in dim
surroundings, set a value in the Lolux mode.
[Setting Values: 36dB, R30dB]
Clip Review
For setting the operation of clip review.
* Clip review functions by operating the user button
assigned with the “Clip Review” function.
0
Last 5sec:
Views about 5 seconds of the clip from the
ending.
0
Top 5sec:
Views about 5 seconds of the clip from the
beginning.
0
Clip:
Views the entire clip.
[Setting Values: RLast 5sec, Top 5sec, Clip]
Spot Meter
For setting the operation of the spot meter.
* Spot meter functions by operating the user button
assigned with the “Spot Meter” function.
(A P80 [Setting Spot Meter] )
0
Max & Min:
Displays the brightest and darkest areas of the
image.
0
Max:
Displays the brightest area of the image.
0
Min:
Displays the darkest area of the image.
0
Manual:
Displays the image brightness at a specified
position.
[Setting Values: RMax & Min, Max, Min, Manual]
Camera Function Menu
111
Menu Display and Detailed Settings