User manual
Table Of Contents
- Introduction
- Preparations
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Focusing by Face Detection
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Setting the ND Filter
- Adjusting the White Balance
- Adjusting the Camera Image
- Using the Image Stabilizer
- Audio Recording
- Monitoring Audio Sound During Recording Using a Headphone
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing Time Code on Another Camera
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Recording Simultaneously at Two Different Definitions
- Splitting the Clips Freely (Clip Cutter Trig)
- Dual Rec
- Backup Rec
- Special Recording
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Connecting to the Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Feature
- Camera Control Function
- Configuring Settings via a Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Others
User Switch Set Item
USER1 - USER7, LCD KEY▲/LCD KEY▶/LCD
KEY▼/LCD KEY◀
By
assigning one of the following functions to each
of the [FOCUS ASSIST/1], [OIS/2], [LOLUX/3], [AE
LOCK/4], [ZEBRA/5], [MARKER/6], [C.REVIEW/7]
buttons or the cross-shaped buttons on the LCD
monitor, these buttons can be used to control the
assigned function (on/off, start, switch).
Set according to the shooting conditions. Usable
only in the Camera mode.
[Setting Values: None, Zebra, Marker, Bars, Focus
Assist, OIS, Flash Band, LCD Backlight, Lolux, AE
Lock, Spot Meter, Face Detect, OK Mark, Clip
Cutter Trig, Backup Trig, Clip Review, Load Picture
File, White Balance, Preset Zoom1, Preset Zoom2,
Preset Zoom3, One Push Focus, One Push Iris,
Expanded Focus, Live Streaming]
Front REC
For
setting the function of the [REC] button located
below the lens at the front of the unit.
0
REC:
Functions
as a record button for starting/ending
recording.
0
AWB:
When the [WHT BAL B/A/PRESET] selection
switch is set to “A” or “B” in the Manual White
Balance mode, it functions as an AWB startup
button. If the [WHT BAL B/A/PRESET] selection
switch is set to “PRESET”, it functions as a
button for switching between two color
temperature settings.
(A P59 [Manual White Balance Mode (Manual
Switching)] )
0
None:
Disabled.
[Setting Values: RREC, AWB, None]
Lolux
To increase the sensitivity when in dim
surroundings, set a value in the Lolux mode.
[Setting Values: 36dB, R30dB]
Clip Review
For specifying the operation when any of the
[USER1]-[
USER7], [LCD KEY▲], [LCD KEY▶],
[LCD KEY▼], or [LCD KEY◀] items is set to “Clip
Review”.
0
Last 5sec:
Views about 5 seconds of the clip from the
ending.
0
Top 5sec:
Views about 5 seconds of the clip from the
beginning.
0
Clip:
Views the entire clip.
[Setting Values: RLast 5sec, Top 5sec, Clip]
Memo :
0
This
item is selectable when any of the [USER1]-
[USER7], [LCD KEY▲], [LCD KEY▶], [LCD
KEY▼], [LCD KEY◀] items is set to “Clip
Review”.
Spot Meter
For specifying the operation when any of the
[USER1]-[
USER7], [LCD KEY▲], [LCD KEY▶],
[LCD KEY▼], or [LCD KEY◀] items is set to “Spot
Meter”.
(A P72 [Setting Spot Meter] )
0
Max & Min:
Displays the brightest and darkest areas of the
image.
0
Max:
Displays the brightest area of the image.
0
Min:
Displays the darkest area of the image.
0
Manual:
Displays the image brightness at a specified
position.
[Setting Values: RMax & Min, Max, Min, Manual]
100
Menu Display and Detailed Settings