User manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- Recording Media
- Usable Cards
- Usable SSD Media
- Estimated Recordable Time of SD Cards
- Estimated Recordable Time of SSD Media
- Inserting an SD Card
- Removing the SD Card
- Switching the SD cards
- Inserting the SSD Media Adapter (Sold Separately)
- Formatting (Initializing) of Recording Media
- Repairing the Recording Media
- Clips Recorded to Recording Media
- Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Tagging Feature
- Overlay
- Others
Time Code Operation Mode
Select the time code operation using the [TC
GEN] switch.
Setting Description
F-RUN The time code operates in the run
mode
at
all times regardless of the
recording status.
It continues to run even when the
power of the camera recorder is
turned off.
Synchronizes with the external
time code when an external time
code generator is connected.
(A P80 [Synchronizing the
Time Code with an External
Time Code Generator] )
R-RUN The time code operates in the run
mode during recording. It
continues to
run in the order of the
recorded clips as long as the SD
card is not replaced. If the SD card
is removed and recording is made
on another card, time code will be
recorded on the new card from
where it was left off in the previous
card.
REGEN The time code operates in the run
mode during recording. When the
SD card is replaced, the last time
code recorded on the card is read
and recorded
on a new card so that
the time code continues in running
order.
(A P77 [Setting Time Code] )
Memo :
0
When [System] B [Record Set
] B [Rec Mode] is
set to “Interval Rec” or “Frame Rec”, and the [TC
GEN] switch is set to “F-RUN”, R-RUN mode is
activated.
0
When [System] B [Record Set]
B [Record
Format] B [System] is set to “High-Speed”, and
the [TC GEN] switch is set to “F-RUN”, R-RUN
mode is activated.
Setting Time Code
Generator
Presetting the Time Code
Time code and user’s bit data generated from the
internal time code generator are recorded.
This section describes how to set [TC/UB]
B [TC
Preset].
(A P126 [ TC Preset ] )
Memo :
0
When [System]
B [Record Set] B [Record
Format] B [WFrame Rate] is set to “50p”, “50i”
or “25p”, setting for “Drop” will be disabled.
(A P161 [WFrame Rate/
Frame Rate] )
0
You can configure the setting without accessing
the [TC/UB] menu screen.
(A P78 [Setting Time Code without Opening
the Menu] )
Required Settings Before Preset
.
PRESET
TC
F-RUN
R-RUN
REGEN
UB
GEN
DISPLAY
1
Set the [TC GEN] switch to “R-RUN” or “F-
RUN”
.
0
[R-RUN]
Preset data in the time code generator
operates in
run mode during recording mode.
Set this when recording continuous time
code in connecting frames.
0
[F-RUN]
Time code starts to operate in run mode from
the preset time in the time code generator.
76
Time Code and User’s Bit
Shooting