User manual

Audio Recording
You can
record audio from the four channels (CH1/
CH2/CH3/CH4) in synchronization with the video
images on this camera recorder.
Select from the options below to record the audio.
0
Microphone connected to
[
MIC IN] terminal
(XLR 5-pin)
0
Microphone or line input connected to the
[AUDIO INPUT1] terminal (XLR 3pin)
0
Microphone or line input connected to the
[AUDIO INPUT2] terminal (XLR 3pin)
.
P
R
AUDIO INPUT
DI
S
Setting the Number of Recording
Channels
0
Set the number of recording channels in
[System] B [Record Set
]
B [Record Format] B
[Audio].
Selecting Audio to Be Recorded in Each
Channel
Select the audio to be recorded in CH1/CH2/CH3/
CH4.
-
Switch
Setting
Connected Devices
CH1
CH3
FRONT
0
Audio input of
microphone 1 from
[MIC IN]
terminal
REAR
0
Audio input from
[
AUDIO INPUT1
]
terminal
WIRELESS
0
Audio input of CH1
from the
“UniSlot
”
wireless receiver
CH2
CH4
FRONT
0
Audio input of
microphone 2 from
[MIC IN] terminal
REAR
0
Audio input from
[AUDIO INPUT2]
terminal
WIRELESS
0
Audio input of CH2 (or
CH1)
from
the “UniSlot”
wireless receiver
When the switch setting is set to “FRONT”
Audio recording is performed according to the
setting in [A/V Set] B [Audio Set] B [Front Mic
Select]/[Front Mic Power]/[Front Mic 1 Ref.]
/[Front
Mic 2 Ref.].
Caution :
0
Set [Front Mic
Select] to “Stereo M/S” to convert
the audio signal to stereo (L/R) signal for
recording when a Mid/Side direct output
microphone is connected.
Do not set to “Stereo L/R” or “Mono” when an L/
R out stereo microphone or a monophonic
microphone is connected.
When the switch setting is set to “REAR”
Select the audio input to the [AUDIO INPUT 1/2]
terminal using the [AUDIO INPUT 1/2] switch.
Setting Description
[LINE] Use this setting when connecting to
an audio
device or other equipment.
[MIC] Use this setting when connecting to
a dynamic microphone.
[MIC+48V] Use this setting when connecting to
a microphone (phantom
microphone) that requires a +48 V
power supply.
Memo :
0
When “LINE” is selected, configure the
reference input level in [A/V Set] B [Audio Set]
B [Rear Line Ref.].
(A P139
[ Rear Line Ref. ] )
0
When “MIC” or
“MIC+48V” is selected, set the
reference input level in [A/V Set] B [Audio Set]
B [Rear Mic 1 Ref.]/[Rear Mic 2 Ref.].
(A
P139 [ Front Mic 1 Ref. ] )
(
A P139 [ Front Mic 2 Ref. ] )
Caution :
0
When
connecting
a device that does not require
a +48 V power supply, make sure that it is not
set to the “MIC+48V” position.
0
When the [AUDIO INPUT 1/2] switch is set to
“MIC”, make sure that a microphone is
connected to the [AUDIO INPUT 1/2] terminal. If
you increase the recording level when a
microphone is not connected, noise from the
input terminal may be recorded.
0
When a microphone is not connected to the
[AUDIO INPUT 1/2] terminal, set the [AUDIO
INPUT 1/2] switch to “LINE”.
When the switch setting is set to “WIRELESS”
Recording
is performed as follows according to the
setting in [A/V Set] B [Audio Set] B [Wireless
Channel].
Audio Recording
71
Shooting