User manual
Table Of Contents
- Introduction
- Preparations
- Settings and Adjustments Before Use
- Power Supply
- Power Status Display
- Turning On/Off the Power
- Initial Settings
- Displays on the LCD Monitor and Viewfinder
- Adjusting the LCD Monitor and Viewfinder
- Adjusting the Back Focus
- Assignment of Functions to User Buttons
- Tally Lamp
- Recording Media
- Usable Cards
- Usable SSD Media
- Estimated Recordable Time of SD Cards
- Estimated Recordable Time of SSD Media
- Inserting an SD Card
- Removing the SD Card
- Switching the SD cards
- Inserting the SSD Media Adapter (Sold Separately)
- Formatting (Initializing) of Recording Media
- Repairing the Recording Media
- Clips Recorded to Recording Media
- Operation Lock Feature
- Shooting
- Basic Shooting Procedures
- Selecting System Definition, File Format and Video Format
- Zoom Operation
- Focus Operation
- Adjusting the Brightness
- Adjusting the Iris
- Setting the Gain
- Setting the Electronic Shutter
- Adjusting the White Balance
- Adjusting the Camera Image
- Audio Recording
- Audio Output during Recording
- Time Code and User’s Bit
- Setting Time Code Generator
- Setting the User’s Bit
- Synchronizing the Time Code with an External Time Code Generator
- Setting Zebra Pattern
- Setting Spot Meter
- Acquiring Positioning Information by GPS
- Viewing Recorded Videos Immediately (Clip Review)
- Displaying the Video Signal Monitor
- Recording Simultaneously at Two Different Definitions
- Series Rec
- Dual Rec
- Backup Rec
- Special Recording
- Splitting the Clips Freely (Clip Cutter Trig)
- Playback
- Menu Display and Detailed Settings
- Display/Status Screen
- Camera Features
- Connecting External Devices
- Network
- Functions of Network Connection
- Preparing Network Connection
- Importing Metadata
- Uploading a Recorded Video Clip
- FTP Resume Feature
- Connecting from a Web Browser
- Editing Metadata
- Uploading a Recording Clip via a Web Browser
- View Remote Control and Camera Control Functions
- Changing the Settings via a Web Browser
- Managing the Network Connection Settings File
- Performing Live Streaming
- Return Video/Audio from the Network (Return over IP)
- IFB (Return Audio)
- Tagging Feature
- Overlay
- Others
9
Server1, Server2, Server3, Server4
* The name that is set in
[Alias] is displayed
individually.
o
Alias
For setting a name to distinguish the settings of this
camera.
The name set in this item will be displayed in the
[Server] options.
*1 The default value is
“Server1/Server2/
Server3/Server4”.
*2 You can enter up to 31 characters and ASCII
characters.
o
Type
For configuring the system for transferring video
and audio to be distributed.
[Setting Values: RRTSP/RTP, ZIXI(SRT), Icecast]
Memo :
0
Operates as IFB when the setting is configured
to “Icecast
”.
0
Use transmission devices that are compatible
with the respective transfer systems.
0
To use the “ZIXI” setting, a dedicated server is
needed separately.
0
SRT protocol update needs to be performed
before using the SRT protocol. Doing so will
make the Zixi protocol unusable.
To enable the use of the Zixi protocol again,
perform Zixi protocol update.
0
The following items that can be set vary
depending on the setting of this item.
o
Protocol
For configuring the protocol of the video/audio
source server to be connected.
[Setting Values: RUDP, TCP]
Memo :
0
This item
is selectable only when [Type] is set to
“RTSP/RTP”.
o
Connection Mode
For configuring the SRT connection mode.
[Setting Values: RCaller, Listener, Rendezvous]
Memo :
0
This item
is selectable only when [Type] is set to
“SRT”.
o
Source Address
For configuring details such as the host name and
IP address
of the video/audio transmission source.
There is no default value (blank).
*1 A maximum of 191 ASCII characters can be
entered when [Type] is configured to a setting
other than “SRT”.
*2 A maximum of 191 characters including
single-byte alphanumeric characters (a to z, 0
to 9) and single-byte hyphen [-] and dot [.] can
be entered when [Type] is configured to
“SRT”.
o
Source Port
Enter the network port number of the video/audio
transmission source using an integer between 1
and 65535.
The default value is
“554
” when [Type] is set to
“RTSP/RTP”, “2077” when it is set to “ZIXI”, and
“5000” when it is set to Icecast.
Memo :
0
When [Type] is set to “RTSP/RTP
”, only even
numbers from 2 to 65530 can be specified for
the port number.
o
Port
Enter a SRT port number using an integer between
1 and 65535.
The default value is
“6510
”.
Memo :
0
This item
is selectable only when [Type] is set to
“SRT”.
o
Stream ID
For configuring the stream ID registered on the
video/audio transmission source.
There is no default value (blank).
*
Enter not more than 63 characters.
Memo :
0
This item is available for setting when [Type
] is
set to “RTSP/RTP” or “ZIXI”.
o
Username
For setting the user name.
There is no default value (blank).
* Enter not more than 63 characters.
Memo :
0
This item
is selectable only when [Type] is set to
“RTSP/RTP”.
150
Network Menu
Menu Display and Detailed Settings