MULTI FORMAT LCD MONITOR DT-V9L5 INSTRUCTIONS For Customer Use: Enter below the Serial No. which is located on the rear of the cabinet. Retain this information for future reference. Model No. : DT-V9L5 Serial No. : DT-V9L5_EN_1.
Safety Precautions The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages and other hazards. Refer all service to qualified service personnel. Do not use the product for a long time if the sound is distorted. Use only the power source specified on the unit. • AC power: 120 V, 50 Hz/60 Hz • DC power: 12 V — 17 V • The AC power supply is controlled by turning on/off the POWER switch on the rear panel.
Safety Precautions (cont.) IMPORTANT SAFETY INSTRUCTIONS 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Table of Contents Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT SAFEGUARDS 2 Operating Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caution for use of the product for many hours Caution for use of the product in the high temperature Maintenance 4 4 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Caution ● Do not rest your arm on the monitor or lean against the monitor. ● Do not touch the LCD panel when installing the monitor. ● Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor or injury. Adjusting the stand height You can select the stand height according to your preference—higher position or lower position. To change the stand height, change the position of the screw hole used for attaching the stand.
Lower position When you want to lower the position of the monitor. Attachment screws Stand Monitor Tilting the monitor You can tilt the monitor as shown below. About 20° 0° When the monitor is not tilted (0°), the guidelines align as illustrated. Guidelines About 10° CAUTION ● Be careful not to pinch your fingers in the gap between the monitor and the stand. ● When the stand is attached to the lower position, you cannot tilt the monitor downward.
Index of Parts and Functions Rear panel Carry handle Security slot Use this handle when carrying the monitor. Attach a security wire to this slot. 1 POWER switch Turns AC power on or off. ● You need to press button (☞ q on page 10) to use the monitor after turning on the POWER switch. 2 AC IN terminal AC power input connector. Connect the provided AC power cord to an AC outlet. ● Attach the provided power cord holder to prevent accidental disconnection of the AC power cord.
7 HDMI terminal Input terminal compatible with HDCP for the HDMI signal. (TYPE-A) 8 REMOTE terminal Terminal for controlling the monitor by an external control. (☞ “External Control” on page 23) 9 AUDIO (MONITOR OUT) terminals (pin jack) Output terminals for the analog audio signal. ● The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO HD/SD SDI (IN 1 or IN 2) input terminal.
Index of Parts and Functions (cont.) Front panel Tally lamp This lamp is controlled by the tally function of the MAKE/TRIGGER terminal. • You can select the color of the tally lamp from “Green” or “Red.” You can also select whether the whole lamp is turned on at once, or whether it is turned on one half at a time.
y SCOPE button/lamp Displays/hides the indication of the wave form monitor and vectorscope (☞ “Scope Setting” on page 17). ● Each time you press this button, the window changes in the following order. No display Histogram Wave form monitor Vectorscope u DC lamp When the DC power voltage is being lowered due to the battery consumption, the lamp changes to orange from green. When the voltage becomes lower than a certain level, the monitor automatically turns off and the lamp turns to red.
Showing Input Signals (cont.) On the Status Display If you press the INPUT SELECT button (☞ 9 on page 10) currently lit, the status of the input signal and setting of MUTING are displayed for about 3 seconds. ● Make the setting to display/hide the status in “Status Display” of the “Information”.
Menu Transition Diagram Main Menu Picture Function Size/Position Adjust Aspect Dynamic Signal Setting Marker Audio Setting Scope Setting Sync Function No Operation Action Backlight Aperture Aperture Level CTI LTI Gamma Color Temperature sub menu reset H Size H Position V Size V Postion sub menu reset Auto Aspect Manual Aspect SD4：3 Size 16：9 Size 1：1 Area Marker Marker Aspect Safety Marker Safety Area Frame Center Marker Line Brightness R-Area Marker R-Marker Aspect R-Safety Marker R-Safety Area Gain Siz
Menu Configuration (cont.) Main Menu Picture Function Setting for the picture quality. Item Backlight Aperture*1 Aperture Level*1 CTI LTI Gamma Color Temperature sub menu reset *1 To do Adjusts the brightness of the display. Activates/deactivates the function at the level set in “Aperture Level”. Compensate the frequency response of the luminance signal of the video signal. Adjust the clearness of the outlines of the chrominance signal. Adjust the clearness of the outlines of the luminance signal.
Signal Setting Settings for input signals. Item Video/Component Select I/P Mode Color System sub menu reset To do Selects the signal type you want to use for VIDEO/COMPONENT terminals. Selects a proper mode corresponding to the input picture. Select the color system. • If the picture is unstable with “Auto,” select the color system according to the input signal. Setting value Video, Component Normal, Cinema Auto, NTSC, PAL, SECAM, NTSC 4.
Menu Configuration (cont.) Audio Setting Settings for EMBEDDED AUDIO signals and audio level meter signal. Item SDI-1 Select SDI-2 Select To do Select the input through which audio is output. Setting value Off, Auto, Digital, Analog Off : Does not output audio. Auto : Output digital audio prior to analog audio. Digital : Output audio from the SDI terminal. Analog : Output audio from the AUDIO IN terminal. HDMI Select Select the input through which audio is output. Off : Does not output audio.
Scope Setting*1 Configure the settings for the wave form monitor and vector scope. Item Gain*2 Size*3 Position To do Adjust the input gain level. Set the window size. Select the window position. Transparent Activates/deactivates the function to make the window translucent. Auto Off Histogram Display Wave Display Off : Normal On : Translucent Set the function to turn off the window automatically 15 minutes after displayed. Select the signal component for the histogram display.
Menu Configuration (cont.) Sync Function Settings for the synchronization with signals. Item No Sync Action To do Select the screen status when no signal is coming in. Setting value Off, Standby, Power Save (power save mode), Gray Back (gray screen) Select the period until the screen status changes as selected in “No Sync Action” after signals 30s, 5min, 15min stop coming in. Activates/deactivates the function to shorten the time taken to display the picture (low Off, On latency function).
Function Key Setting Function1 Function Display Specify the function assigned to the F1 button. Specify the function assigned to the F1 button. * See pages 13 to 22 for details of the functions assigned to Function 1. Select whether to display the status of the assigned function when you press the F1 button. Off : No status display. Perform the registration function. Mode-1 : Display the status. Perform the registration function. Mode-2 : Display the status. Do not perform the registration function.
Menu Configuration (cont.) Remote Setting Settings for the external control. Item Parallel Type Pin1 Pin2 Pin3 Pin4 Pin5 Pin6 Pin7 Pin8 To do Select a control method of the MAKE/TRIGGER terminal. Setting value Make, Trigger, Set Assign the control functions to the pins of the MAKE/TRIGGER terminal. • Assign a function to each pin terminal by selecting “Set” in “Parallel Type” mentioned above.
IMD Settings for IMD (In-monitor Display). (☞ Page 22) Item IMD Display IMD Protocol Address IMD Size Text Color Tally 1 Color Tally 2 Color Background Color reset To do Display setting Off :Not displayed On :Displayed Serial communication protocol setting Off : Supports JVC protocol TSL V4.0 : Supports TSL UMD Protocol V4.
Menu Configuration (cont.) ● Setting of “Character Setting” 1 2 3 Change the input to one that you want to assign a video source name for. Select “Character Setting”. Press buttons to select the first character. ● Each time you press button, the character changes as follows. Press button to reverse the order. Space 4 Press button to move the arrow to the next space. ● The characters entered before moving the arrow are memorized. Repeat steps 3 and 4 (10 characters at maximum).
External Control About the external control This monitor has three external control terminals. ● MAKE/TRIGGER terminal (RJ-45): The following external control systems are available. (1) MAKE (make contact) system: Controls the monitor by short-circuiting the corresponding pin terminal to the GND pin terminal, or disconnecting (opening) it. (2) TRIGGER (trigger) system: Controls the monitor by sending the pulse signal instantaneously to the corresponding pin terminal.
External Control (cont.
All commands consist of the following segments. Header Monitor ID Function Data Cr (0Dh) On Header “!” : Operation commands from the personal computer, etc. (☞ below table). “?” : Reference commands from the personal computer, etc. “@” : Status returns from the monitor To start communication, send the connection command from the personal computer etc. To terminate the communication, send the termination command from the personal computer etc.
Troubleshooting Solutions to common problems related to the monitor are described here. If none of the solutions presented here solve the problem, unplug the monitor and consult an authorized dealer or service center. Symptom Probable cause and corrective action No power supply. ● ● ● ● No picture with the power on. ● ● ● ● No sound. ● ● ● ● ● “Out of range” appears. ● “No Sync” appears. ● ● ● ● Wrong color, no color. ● ● ● ● The picture becomes blurred.
Self-check program This monitor has a self-check function, which allows it to detect malfunctions and alert you. This makes troubleshooting easier. Whenever a problem occurs, one or some of the INPUT SELECT lamps will flash. If this happens, follow the steps below and contact your dealer to resolve the problem. INPUT SCOPE HDMI When the screen goes blank, and one or some of the INPUT SELECT lamps (SDI 1/SDI 2) on the front control panel start flashing... 1 Check which lamps are flashing.
Specifications General Model name Type Screen size Aspect ratio DT-V9L5 Multi format LCD monitor Type 8.2 wide format 16:10 Compliant video signal format Format ☞ “Available signals” on page 30 HD SDI: SMPTE292M SD SDI: ITU-R BT.656, SMPTE259M EMBEDDED AUDIO 16CH: SMPTE299M, SMPTE272M Internal speaker: 1.0 W Audio output Operating conditions Operating temperature: 5°C – 35°C (41°F – 95°F) Operating humidity: 20% – 80% (non-condensing) (Slightly variable depending on ambient conditions for installation.
Dimensions Unit: mm (inch) DT-V9L5 116 (4 5/8) 26.5 (1 1/8) 217 (8 5/8) 1.3 (1/16) 176 (7) 218 (8 5/8)*/ 181 (7 1/4)** 202 (8) 13 (5/8) 185 (7 3/8) 186 (7 3/8) *at the higher position **at the lower position 100 37.5 (1 1/2) 55 (2 1/4) 75 100 75 VESA mounting holes (8-M4, depth:10mm) Notice on transportation This monitor is precision equipment and needs dedicated packing material for transportation.
Specifications (cont.) Available signals The following signals are available for this monitor. Video signals No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Signal name NTSC NTSC 4.43 PAL-M PAL60 PAL PAL-N SECAM B/W50 B/W60 480/60i 480/59.94i 576/50i 480/60p 480/59.94p 576/50p 640x480/60p 640x480/59.94p 720/60p 720/59.94p 720/50p 720/30p 720/29.97p 720/25p 720/24p 720/23.98p 1080/60i 1080/59.94i 1035/60i 1035/59.
MEMO 31 DT-V9L5_EN_1.
MULTI FORMAT LCD MONITOR DT-V9L5 © 2012 JVC KENWOOD Corporation DT-V9L5_EN_1.
