User Manual

45
Specifications
General
Model name DT-E15L4
Type Multi format LCD monitor
Screen size Type 15 wide format
Aspect ratio 16:9
Horizontal/vertical frequency
(computer signal)
H: 31.469 kHz – 75.000 kHz
V: 49.990 Hz – 75.062 Hz
* Some signals within this frequency range may not be displayed (“Out of range” is displayed).
Compliant video signal format
“Available signals” on page 47
Format HD SDI: BTA S-004C, SMPTE292M
SD SDI: ITU-R BT.656: 525/625
SMPTE259M: 525
EMBEDDED AUDIO: SMPTE299M, SMPTE272M
Audio output Internal speaker: 1.0 W
Operating conditions Operating temperature: 5°C – 35°C
Operating humidity: 20% – 80% (non-condensing)
(Slightly variable depending on ambient conditions for installation.)
Power requirements AC 120 V / AC 220 – 240 V, 50 Hz/60 Hz
Rated current 0.6 A (AC 120 V)
0.35 A (AC 220 – 240 V)
External dimensions
(excluding protruding parts)
with the stand without the stand
Width: 373 mm 373 mm
Height: 270.1 mm 265 mm
Depth: 181 mm 99 mm
Weight
5.9 kg (with the stand)
4.3 kg (without the stand)
Accessories AC power cord x 2
LCD panel
Type 15˝ wide, active matrix TFT
Effective screen size Width: 344 mm
Height: 194 mm
Diagonal: 395 mm
Number of pixels displayed 1366 x 768
Number of colors displayed 16.70 million
Viewing angle (TYP.) 170° (Horizontally), 160° (Vertically)
Brightness (TYP.) 300 cd/m
2
Contrast ratio (TYP.) 500:1
Input/output terminals
Video
VIDEO Input/output of composite signal: 1 line, BNC connector x 2, 1 V (p-p), 75 Ω
* The input (IN) and output (OUT) terminals are bridge-connected
(auto termination).
HDMI
HDMI signal input (compatible with HDCP)
: HDMI connector x 1
COMPO./RGB
(R, G, B, HS, VS or Y, Pb/B-Y,
Pr/R-Y)
Analog Component signal input/Analog RGB signal input:
1 Line, mini D-SUB 15pin x1
Y: 1 V(p-p), 75 Ω(with sync)
G, B/PB/B-Y, R/PR/R-Y: 0.7 V (p-p), 75 Ω
HS, VS: 0.3 V (p-p) to 5 V (p-p)
* For HS and VS, change the Low/High terminals manually.
E. AUDIO HD/SD SDI (IN 1) Digital signal input (compatible with EMBEDDED AUDIO signals):
auto detection, 2 line, BNC connector x 2
E. AUDIO HD/SD SDI (IN 2)
E. AUDIO HD/SD SDI
(SWITCHED OUT)
Digital signal output (compatible with EMBEDDED AUDIO signals):
1 line switched out, BNC connector x 1
Audio
AUDIO (IN) Analog audio signal input: 1 line, RCA connector x 2, 500 mV (rms), high impedance
AUDIO (MONITOR OUT) Analog audio signal output: 1 line, RCA connector x 2, 500 mV (rms)
External
control
REMOTE (MAKE/TRIGGER)
“Using the Make/Trigger system” on page 40
REMOTE (RS-485)
“Using the serial communication” on page 41
REMOTE (RS-232C)
DT-E15L4EN.indb45DT-E15L4EN.indb45 2012/11/0117:10:522012/11/0117:10:52