DVD Video Recorder & Video Cassette Recorder Instructions
Table Of Contents
- SAFETY FIRST
- CONTENTS
- DISC INFORMATION
- INDEX
- INSTALLING YOUR NEW UNIT
- INITIAL SETTINGS
- OPERATIONS ON DVD DECK
- Basic Playback
- Playback Features
- Locating A Desired Scene Using The DVD Menu
- Locating The Start Point Of The Item Or Skip The Item
- High-Speed Search
- Still Picture/Frame-By-Frame Playback
- Slow Motion
- Skip Search
- Resume Function
- Marking Positions To Play Back Again Later
- Checking The Time Information
- Angle Selection
- Subtitle Selection
- Audio Language/Sound Selection
- Audio Channel Selection
- Playback Control (PBC) Function
- Live Memory Playback
- Recording/playback Status Display
- To Play Back From The Beginning Of The Programme While Recording
- To Move Back The Playback Position Slightly While Recording (One Touch Replay function)
- To Watch A Programme Previously Recorded While Recording
- Overview Of Live Memory Playback
- Display During Live Memory Playback
- Buttons To Be Used During Live Memory Playback
- Using The On-screen Bar
- How To Access The On-screen Bar
- Basic Operation On The On-screen Bar
- Repeat Playback
- A-B Repeat Playback
- Locating The Beginning Of A Desired Selection
- Time Search
- Simulated Surround Effect
- Adjusting The Picture Quality
- Setting The Progressive Mode
- Programme Playback
- Random Playback
- Select The Switching Interval Of The Slide Show
- Parental Lock
- OPERATIONS ON DVD DECK
- OPERATIONS ON VCR DECK
- NAVIGATION (DVD DECK ONLY)
- EDITING
- REMOTE CONTROL
- SYSTEM CONNECTIONS
- SUBSIDIARY SETTINGS
- TROUBLESHOOTING
- GLOSSARY
- SPECIFICATIONS
- APPENDIX
- LIST OF TERMS
- Memo
Masterpage:Right+
EN 79
Filename [DR-MV1SEK_09Editing.fm]
Page 79 April 15, 2004 3:18 pm
SYSTEM CONNECTIONS
These instructions enable you to connect your unit to a Dolby
Digital decoder or an amplifier with built-in DTS.
1 Connect the unit and a Dolby Digital decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
● For Dolby Digital sound, set “DIGITAL AUDIO OUT” to “DOLBY
DIGITAL/PCM”. (墌 pg. 80)
● For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/PCM”.
(墌 pg. 80)
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards to its
Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to the
speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely affect
the playback picture.
When you can’t switch the audio channel of a bilingual
programme
When the unit is connected with a digital audio device using an
optional optical cable and “DIGITAL AUDIO OUT” is set to “DOLBY
DIGITAL/PCM”, it is not possible to switch the audio channel of a
bilingual programme recorded on a DVD-RAM or DVD-RW (VR
mode) disc. In this case, perform the following steps using the
remote control to switch “DIGITAL AUDIO OUT” from “DOLBY
DIGITAL/PCM” to “PCM ONLY”.
A Press SET UP to access the Main Menu screen.
B Press we to select “DVD SET UP”, then press ENTER.
C Press we to select “AUDIO OUTPUT”, then press ENTER.
D Press rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
E Press rt to select “PCM ONLY”, then press ENTER.
(墌 pg. 80)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel. (墌 pg. 30)
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
2
Note for connection:
Remove the protection cap from the cable.
Coaxial cable
(not provided)
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO input
Optical cable
(not provided)
DIGITAL AUDIO OUT (OPTICAL)
DIGITAL AUDIO OUT (COAXIAL)
DR-MV1SEK_00.book Page 79 Thursday, April 15, 2004 3:30 PM