DVD Video Recorder & Video Cassette Recorder Instructions

Filename [DR-MV1SEK_07VCR Operation.fm]
Masterpage:Left+
54 EN
Page 54 April 15, 2004 1:27 pm
OPERATIONS ON VCR DECK
1 Load a cassette with the record safety tab intact.
● The unit’s power comes on automatically and the counter is reset to
0:00:00.
2 Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
3 Press PR +/– or the number keys to select the channel you
wish to record.
4 Press REC MODE repeatedly to set the recording mode.
5 Press 7 on the unit to start recording. Or press and hold 7 and
press 4 on the remote control.
● The VCR recording lamp lights up on the unit.
● If “O.S.D.” is set to “ON” (墌 pg. 82), “MARK” blinks on the screen
while an index code is being marked.
6 Press 9 to pause recording.
● You can select channel during the Record Pause mode.
● To resume recording, press 4.
7 Press 8 to stop recording.
● The VCR recording lamp lights off on the unit.
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording or timer recording (墌 pg. 54, 56, 57), the recording will
resume automatically when power is restored to the unit unless the
unit’s memory backup has expired.
Watch Another Programme While Recording On The
Unit
While recording is going on, you can watch another programme on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (
墌 pg. 76)
1 During recording, press TV/VCR to select TV mode if your unit
is connected to the TV via the RF connection.
● VCR mode is disengaged, then the VCR indicator lights off and “TV”
appears on the front display panel.
● The programme received on the TV’s tuner is displayed on the TV
screen.
2 Slide the TV/CABLE/SAT/DVD switch to TV.
3 Press PR +/– repeatedly to select the desired channel.
Accidental erasure
prevention
To prevent accidental recording on
a recorded cassette, remove its
safety tab. To record on it later,
cover the hole with adhesive tape.
Elapsed Recording Time
Indication
1 Press DISPLAY until a counter reading appears on the front
display panel.
2 Press CANCEL (&) to reset the counter before starting
recording or playback.
● The counter is reset to “0:00:00” and shows the exact elapsed time
as the tape runs. You can check the exact time of a recording or
playback.
Basic Recording
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
B.E.S.T. takes place at the beginning of both the first SP and the
first LP recording after inserting the cassette. (墌 pg. 55)
If “DIRECT REC” is set to “ON”, the programme that appears on
the TV screen will be recorded. (墌 pg. 81)
7
8
4
9
VCR/DVD PR +/–REC MODE
1
4
7
2
5
8
0
3
6
9
7
REC MODE
98
PR +/–
0 – 9
4
VCR/DVD
DISPLAY
CANCEL (&)
TV/VCR
AUDIO
SAT
Recording Features
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
● Press VCR/DVD repeatedly so that the VCR lamp lights up on the
unit.
VCR indicator lights off.
Record safety tab
DR-MV1SEK_00.book Page 54 Thursday, April 15, 2004 3:30 PM