Projector Service Manual
Table Of Contents
- DECLARATION OF CONFORMITY
- BZSAFE.PDF
- CH1INTRO.PDF
- CH2SYSDE.PDF
- Functional Descriptions
- Contents
- Cover and Base
- External Power Requirements
- Electronics Systems Overview
- System Power
- Card Cage
- Circuit Boards
- Raster Timing Generator Board (RTG) p/n 100568
- Sync Generator
- Sync Detector and Selector
- Serration and Equalization Lockout
- Phase Locked Loop
- VSYNC Detector, Field Separator, and Mux
- Adjustment Counters
- Serial Communication
- Raster Timing Generator I/O
- Interlocks and Protection
- Horizontal Deflection Board P/N 102523 (HDB)
- Vertical Oscillator
- Horizontal Phase Locked Loop
- Horizontal Centering
- Horizontal Power Supply
- Flyback Switching
- Geometric Correction
- Output Section
- Horizontal Sweep Failure Detection
- Serial Communication
- Horizontal Deflection Board I/O
- Interlocks and Protection
- Vertical Deflection Board P/N 102521(VDB)
- Vertical Preamps
- Vertical Amplifiers
- Sweep Failure Detection
- Side Pincushion and Keystone Correction
- Horizontal Linearity Correction
- Top and Bottom Pincushion and Keystone Correction
- Correction Amplifiers
- Serial Communication
- General I/O
- Interlocks and Shutdowns
- Video Processor Board P/N 104672 (VPB)
- Decoder
- Video/Sync Mux
- V & H Sync Strip
- SG Sync Strip
- B, G, and R Brightness and Contrast Amplifiers
- On-Screen Switch
- Gamma Correction
- Switch Logic and Video Enable
- RGB Sensitivity and Threshold Amplifier
- ILA® Bias
- Dynamic Focus Amplifier
- Serial Communication
- General I/O
- Interlocks and Protection
- Video Amplifier Board P/N 103567 or 103774 (VAB)
- Video Signal
- Failure Detection
- Beam Current Sense
- DC Restore
- Arc Protection
- Blanking
- Enable Circuit
- Focus
- Filament Supply
- General I/O
- System Controller Board P/N 104668 (SCB)
- General Functional Description
- CPU
- Working and Compressed Memory
- Expanded Memory
- Correction Address Generator
- DACs
- DSP
- Overlay Memory
- Overlay Address Generator
- Overlay Interface
- LED Display Buffers and Logic
- RS232 Interface
- IR Interface
- IIC Interface
- Serial Interface
- General I/O
- Backplane Board p/n 100571
- Optical Section
- Image Light Amplifier
- Functional Descriptions
- CH3ADJST.PDF
- CH4MAINT.PDF
- Maintenance Remove/Replace)
- Contents
- Introduction
- Projector Covers
- Ventilation Filters
- Arc Lamp Assembly
- System Power Supply
- Electronics Module
- Cathode Ray Tube (CRT)
- Video Amplifier Board (VAB)
- CRT Yoke
- High Voltage Power Supply (HVPS)
- Card Cage (Printed Circuit Boards)
- Image Light Amplifier Assembly
- Projection Lens
- (SCB) Socket Battery Replacement
- Recommended Spares
- Maintenance Remove/Replace)
- CH5TRBSH.PDF
- HGLOSS.PDF

Chapter 2—Functional Description
Model 330, 340SC and 370SC Service Manual 2-49
IIC
O
VIDOK
Tells SCB that no VABs are reporting problems.
IIC
O
SWEEPOK
Tells SCB that all sweeps are operating.
IIC
O
BEAMDET
Tells SCB that beam current limiting is occurring.
BUS
I/O
Information
Description
Serial
I
REDBIAS
Commanded amplitude of red LCLV bias.
Serial
I
GRNBIAS
Commanded amplitude of green LCLV bias.
Serial
I
BLUBIAS
Commanded amplitude of blue LCLV bias.
Serial
I
RCONT
Commanded red contrast.
Serial
I
GCONT
Commanded green contrast.
Serial
I
BCONT
Commanded blue contrast.
Serial
I
BRIGHT
Commanded brightness level.
General I/O
This section provides a comprehensive description of the inputs to and outputs
from the VPB. The I/O description are arranged by the source/destination of the
signal and so the assemblies communicated with are used as the primary heading
of each group of signals and then are further subdivided into inputs and outputs. In
each case, the signal's direction is noted, with input referring to an input to the
RTG, and output to an output from the VPB. (e.g.: under Raster Timing Generator
'Input'; VSYNC refers to the signal VSYNC that is an input to the VPB from the
Raster Timing Generator). When test points are provided for the I/O they are
noted.
Table 2-11. Video Processor Board I/O Signals
System Controller Board
Input
Description
IICCLK
IIC clock line. Unidirectional clock line for control of
synchronous data transfer over IIC data bus.
BONSCRN
Along with RONSCRN, GONSCRN, VONSCRN,
VIDBLANK, and DCRSTR (the later two on from the
RTG board) determines whether there is full brightness,
black, gray-scale, or external video presented in blue at a
given point on the screen.
RONSCRN
Similar to BONSCRN.
GONSCRN
Similar to BONSCRN.
VONSCRN
Determines if internal test patterns will be shown.
VIDTEST
Internal gray-scale video input information. Real time data 0V
to 1V.
RSENS
Sensitivity (Z-axis gain) correction information for red. Real
time data at 0V to 1V.
GSENS
Similar to RSENS.
BSENS
Similar to RSENS.










