Projector Service Manual
Table Of Contents
- DECLARATION OF CONFORMITY
- BZSAFE.PDF
- CH1INTRO.PDF
- CH2SYSDE.PDF
- Functional Descriptions
- Contents
- Cover and Base
- External Power Requirements
- Electronics Systems Overview
- System Power
- Card Cage
- Circuit Boards
- Raster Timing Generator Board (RTG) p/n 100568
- Sync Generator
- Sync Detector and Selector
- Serration and Equalization Lockout
- Phase Locked Loop
- VSYNC Detector, Field Separator, and Mux
- Adjustment Counters
- Serial Communication
- Raster Timing Generator I/O
- Interlocks and Protection
- Horizontal Deflection Board P/N 102523 (HDB)
- Vertical Oscillator
- Horizontal Phase Locked Loop
- Horizontal Centering
- Horizontal Power Supply
- Flyback Switching
- Geometric Correction
- Output Section
- Horizontal Sweep Failure Detection
- Serial Communication
- Horizontal Deflection Board I/O
- Interlocks and Protection
- Vertical Deflection Board P/N 102521(VDB)
- Vertical Preamps
- Vertical Amplifiers
- Sweep Failure Detection
- Side Pincushion and Keystone Correction
- Horizontal Linearity Correction
- Top and Bottom Pincushion and Keystone Correction
- Correction Amplifiers
- Serial Communication
- General I/O
- Interlocks and Shutdowns
- Video Processor Board P/N 104672 (VPB)
- Decoder
- Video/Sync Mux
- V & H Sync Strip
- SG Sync Strip
- B, G, and R Brightness and Contrast Amplifiers
- On-Screen Switch
- Gamma Correction
- Switch Logic and Video Enable
- RGB Sensitivity and Threshold Amplifier
- ILA® Bias
- Dynamic Focus Amplifier
- Serial Communication
- General I/O
- Interlocks and Protection
- Video Amplifier Board P/N 103567 or 103774 (VAB)
- Video Signal
- Failure Detection
- Beam Current Sense
- DC Restore
- Arc Protection
- Blanking
- Enable Circuit
- Focus
- Filament Supply
- General I/O
- System Controller Board P/N 104668 (SCB)
- General Functional Description
- CPU
- Working and Compressed Memory
- Expanded Memory
- Correction Address Generator
- DACs
- DSP
- Overlay Memory
- Overlay Address Generator
- Overlay Interface
- LED Display Buffers and Logic
- RS232 Interface
- IR Interface
- IIC Interface
- Serial Interface
- General I/O
- Backplane Board p/n 100571
- Optical Section
- Image Light Amplifier
- Functional Descriptions
- CH3ADJST.PDF
- CH4MAINT.PDF
- Maintenance Remove/Replace)
- Contents
- Introduction
- Projector Covers
- Ventilation Filters
- Arc Lamp Assembly
- System Power Supply
- Electronics Module
- Cathode Ray Tube (CRT)
- Video Amplifier Board (VAB)
- CRT Yoke
- High Voltage Power Supply (HVPS)
- Card Cage (Printed Circuit Boards)
- Image Light Amplifier Assembly
- Projection Lens
- (SCB) Socket Battery Replacement
- Recommended Spares
- Maintenance Remove/Replace)
- CH5TRBSH.PDF
- HGLOSS.PDF
Chapter 2—Functional Description
Model 330, 340SC and 370SC Service Manual 2-43
Video Processor Board P/N 104672 (VPB)
The Video Processor Board (VPB) plugs into the electronics card cage.
It is the rear-most card in the card cage. The VPB is the only card in the card cage
that is held in by fasteners. There are four screws that tie the input tray to the rear
panel of the card cage. The input tray is an aluminum panel that attaches to the
VPB input BNC connectors. The input tray is a separate assembly and is not
included with the VPB when a new or repaired board is shipped.
The following functions are provided by the VPB:
Image and sync signal input.
Image and sync signal multiplexing.
Sync signal stripping.
Brightness and contrast control.
CRT protection logic.
Internal and external display multiplexing.
Image signal gamma correction.
LCLV uniformity correction.
LCLV bias.
Dynamic focus signal modification.
The block diagram (Figure 2-15) description, along with the I/O description in the
following section, provide information to perform module-level troubleshooting.