Projector Service Manual
Table Of Contents
- DECLARATION OF CONFORMITY
- BZSAFE.PDF
- CH1INTRO.PDF
- CH2SYSDE.PDF
- Functional Descriptions
- Contents
- Cover and Base
- External Power Requirements
- Electronics Systems Overview
- System Power
- Card Cage
- Circuit Boards
- Raster Timing Generator Board (RTG) p/n 100568
- Sync Generator
- Sync Detector and Selector
- Serration and Equalization Lockout
- Phase Locked Loop
- VSYNC Detector, Field Separator, and Mux
- Adjustment Counters
- Serial Communication
- Raster Timing Generator I/O
- Interlocks and Protection
- Horizontal Deflection Board P/N 102523 (HDB)
- Vertical Oscillator
- Horizontal Phase Locked Loop
- Horizontal Centering
- Horizontal Power Supply
- Flyback Switching
- Geometric Correction
- Output Section
- Horizontal Sweep Failure Detection
- Serial Communication
- Horizontal Deflection Board I/O
- Interlocks and Protection
- Vertical Deflection Board P/N 102521(VDB)
- Vertical Preamps
- Vertical Amplifiers
- Sweep Failure Detection
- Side Pincushion and Keystone Correction
- Horizontal Linearity Correction
- Top and Bottom Pincushion and Keystone Correction
- Correction Amplifiers
- Serial Communication
- General I/O
- Interlocks and Shutdowns
- Video Processor Board P/N 104672 (VPB)
- Decoder
- Video/Sync Mux
- V & H Sync Strip
- SG Sync Strip
- B, G, and R Brightness and Contrast Amplifiers
- On-Screen Switch
- Gamma Correction
- Switch Logic and Video Enable
- RGB Sensitivity and Threshold Amplifier
- ILA® Bias
- Dynamic Focus Amplifier
- Serial Communication
- General I/O
- Interlocks and Protection
- Video Amplifier Board P/N 103567 or 103774 (VAB)
- Video Signal
- Failure Detection
- Beam Current Sense
- DC Restore
- Arc Protection
- Blanking
- Enable Circuit
- Focus
- Filament Supply
- General I/O
- System Controller Board P/N 104668 (SCB)
- General Functional Description
- CPU
- Working and Compressed Memory
- Expanded Memory
- Correction Address Generator
- DACs
- DSP
- Overlay Memory
- Overlay Address Generator
- Overlay Interface
- LED Display Buffers and Logic
- RS232 Interface
- IR Interface
- IIC Interface
- Serial Interface
- General I/O
- Backplane Board p/n 100571
- Optical Section
- Image Light Amplifier
- Functional Descriptions
- CH3ADJST.PDF
- CH4MAINT.PDF
- Maintenance Remove/Replace)
- Contents
- Introduction
- Projector Covers
- Ventilation Filters
- Arc Lamp Assembly
- System Power Supply
- Electronics Module
- Cathode Ray Tube (CRT)
- Video Amplifier Board (VAB)
- CRT Yoke
- High Voltage Power Supply (HVPS)
- Card Cage (Printed Circuit Boards)
- Image Light Amplifier Assembly
- Projection Lens
- (SCB) Socket Battery Replacement
- Recommended Spares
- Maintenance Remove/Replace)
- CH5TRBSH.PDF
- HGLOSS.PDF
Chapter 2—Functional Description
Model 330, 340SC and 370SC Service Manual 2-33
Vertical raster centering.
Top and bottom pincushion correction.
Top and bottom keystone adjustment.
Horizontal overall and edge linearity adjustment.
Left and right pincushion and keystone correction
waveform generation.
Sweep reversal for normal and inverted operation.
Generation of wave forms used for dynamic focus.
The block diagram (see Figure 2-13) description, along with the I/O description in the
following section, provide information for module level troubleshooting.
Component numbering on the VDB, in general, follows the pattern that 2XX refers to
components for Green deflection, 3XX refers to Blue, 4XX refers to Red (e.g.: R428 is a
resistor in the red deflection amplifier). Likewise, the correction amplifiers are numbered
5XX for Green, 6XX for Blue, and 7XX for Red.