Projector Service Manual
Table Of Contents
- DECLARATION OF CONFORMITY
- BZSAFE.PDF
- CH1INTRO.PDF
- CH2SYSDE.PDF
- Functional Descriptions
- Contents
- Cover and Base
- External Power Requirements
- Electronics Systems Overview
- System Power
- Card Cage
- Circuit Boards
- Raster Timing Generator Board (RTG) p/n 100568
- Sync Generator
- Sync Detector and Selector
- Serration and Equalization Lockout
- Phase Locked Loop
- VSYNC Detector, Field Separator, and Mux
- Adjustment Counters
- Serial Communication
- Raster Timing Generator I/O
- Interlocks and Protection
- Horizontal Deflection Board P/N 102523 (HDB)
- Vertical Oscillator
- Horizontal Phase Locked Loop
- Horizontal Centering
- Horizontal Power Supply
- Flyback Switching
- Geometric Correction
- Output Section
- Horizontal Sweep Failure Detection
- Serial Communication
- Horizontal Deflection Board I/O
- Interlocks and Protection
- Vertical Deflection Board P/N 102521(VDB)
- Vertical Preamps
- Vertical Amplifiers
- Sweep Failure Detection
- Side Pincushion and Keystone Correction
- Horizontal Linearity Correction
- Top and Bottom Pincushion and Keystone Correction
- Correction Amplifiers
- Serial Communication
- General I/O
- Interlocks and Shutdowns
- Video Processor Board P/N 104672 (VPB)
- Decoder
- Video/Sync Mux
- V & H Sync Strip
- SG Sync Strip
- B, G, and R Brightness and Contrast Amplifiers
- On-Screen Switch
- Gamma Correction
- Switch Logic and Video Enable
- RGB Sensitivity and Threshold Amplifier
- ILA® Bias
- Dynamic Focus Amplifier
- Serial Communication
- General I/O
- Interlocks and Protection
- Video Amplifier Board P/N 103567 or 103774 (VAB)
- Video Signal
- Failure Detection
- Beam Current Sense
- DC Restore
- Arc Protection
- Blanking
- Enable Circuit
- Focus
- Filament Supply
- General I/O
- System Controller Board P/N 104668 (SCB)
- General Functional Description
- CPU
- Working and Compressed Memory
- Expanded Memory
- Correction Address Generator
- DACs
- DSP
- Overlay Memory
- Overlay Address Generator
- Overlay Interface
- LED Display Buffers and Logic
- RS232 Interface
- IR Interface
- IIC Interface
- Serial Interface
- General I/O
- Backplane Board p/n 100571
- Optical Section
- Image Light Amplifier
- Functional Descriptions
- CH3ADJST.PDF
- CH4MAINT.PDF
- Maintenance Remove/Replace)
- Contents
- Introduction
- Projector Covers
- Ventilation Filters
- Arc Lamp Assembly
- System Power Supply
- Electronics Module
- Cathode Ray Tube (CRT)
- Video Amplifier Board (VAB)
- CRT Yoke
- High Voltage Power Supply (HVPS)
- Card Cage (Printed Circuit Boards)
- Image Light Amplifier Assembly
- Projection Lens
- (SCB) Socket Battery Replacement
- Recommended Spares
- Maintenance Remove/Replace)
- CH5TRBSH.PDF
- HGLOSS.PDF
Safety
Model 330, 340SC, and 370SC Service Manual v
Safety Information
Introduction
Before operating or working on a Model 330, 340SC and 370SC Projector, especially
with the cover off, please read this safety information section thoroughly. Procedures
requiring the opening of the projector covers and/or contact with electrical components
should be performed by qualified service personnel. Strictly adhere to all notes and
warnings.
Safety Equipment
Safety equipment specified in the Hughes-JVC Series 300 Projector Service and
Operator’s Training Course and certification program or equivalent should be used for
maintenance of the equipment.
Warnings and Cautions
Warnings and Cautions
Warnings and Cautions in this manual should be read thoroughly and strictly adhered to.
Warning and Caution symbols and definitions are as follows:
WARNING!!!
Warns user of a potential electric shock hazard
and/or specific procedure or situation that could result in personal injury if
improperly performed.
CAUTION!
Warns user of a potential safety hazard or potential light
hazards that could cause severe eye injury or a specific procedure or situation
that could result in damage to the equipment if improperly used.
The following important safety instructions are designed to insure your safety and the
long life of your projector. Be sure to read these safety instructions thoroughly and adhere
to all warnings given below.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference and (2) this device