Projector Service Manual
Table Of Contents
- DECLARATION OF CONFORMITY
- BZSAFE.PDF
- CH1INTRO.PDF
- CH2SYSDE.PDF
- Functional Descriptions
- Contents
- Cover and Base
- External Power Requirements
- Electronics Systems Overview
- System Power
- Card Cage
- Circuit Boards
- Raster Timing Generator Board (RTG) p/n 100568
- Sync Generator
- Sync Detector and Selector
- Serration and Equalization Lockout
- Phase Locked Loop
- VSYNC Detector, Field Separator, and Mux
- Adjustment Counters
- Serial Communication
- Raster Timing Generator I/O
- Interlocks and Protection
- Horizontal Deflection Board P/N 102523 (HDB)
- Vertical Oscillator
- Horizontal Phase Locked Loop
- Horizontal Centering
- Horizontal Power Supply
- Flyback Switching
- Geometric Correction
- Output Section
- Horizontal Sweep Failure Detection
- Serial Communication
- Horizontal Deflection Board I/O
- Interlocks and Protection
- Vertical Deflection Board P/N 102521(VDB)
- Vertical Preamps
- Vertical Amplifiers
- Sweep Failure Detection
- Side Pincushion and Keystone Correction
- Horizontal Linearity Correction
- Top and Bottom Pincushion and Keystone Correction
- Correction Amplifiers
- Serial Communication
- General I/O
- Interlocks and Shutdowns
- Video Processor Board P/N 104672 (VPB)
- Decoder
- Video/Sync Mux
- V & H Sync Strip
- SG Sync Strip
- B, G, and R Brightness and Contrast Amplifiers
- On-Screen Switch
- Gamma Correction
- Switch Logic and Video Enable
- RGB Sensitivity and Threshold Amplifier
- ILA® Bias
- Dynamic Focus Amplifier
- Serial Communication
- General I/O
- Interlocks and Protection
- Video Amplifier Board P/N 103567 or 103774 (VAB)
- Video Signal
- Failure Detection
- Beam Current Sense
- DC Restore
- Arc Protection
- Blanking
- Enable Circuit
- Focus
- Filament Supply
- General I/O
- System Controller Board P/N 104668 (SCB)
- General Functional Description
- CPU
- Working and Compressed Memory
- Expanded Memory
- Correction Address Generator
- DACs
- DSP
- Overlay Memory
- Overlay Address Generator
- Overlay Interface
- LED Display Buffers and Logic
- RS232 Interface
- IR Interface
- IIC Interface
- Serial Interface
- General I/O
- Backplane Board p/n 100571
- Optical Section
- Image Light Amplifier
- Functional Descriptions
- CH3ADJST.PDF
- CH4MAINT.PDF
- Maintenance Remove/Replace)
- Contents
- Introduction
- Projector Covers
- Ventilation Filters
- Arc Lamp Assembly
- System Power Supply
- Electronics Module
- Cathode Ray Tube (CRT)
- Video Amplifier Board (VAB)
- CRT Yoke
- High Voltage Power Supply (HVPS)
- Card Cage (Printed Circuit Boards)
- Image Light Amplifier Assembly
- Projection Lens
- (SCB) Socket Battery Replacement
- Recommended Spares
- Maintenance Remove/Replace)
- CH5TRBSH.PDF
- HGLOSS.PDF
Chapter 2—Functional Descriptions
Model 330, 340SC and 370SC Service Manual 2–9
*Current depends on projector model (see Table 0-1 in Safety Chapter).
** Model 340SC = 2000 Watts; Model 370SC = 3000 Watts.
Figure 2-4
System Power Supply Input/Output Diagram
Arc Lamp Ignitor
The ignitor consists of a step-up power supply, a spark gap, and a transformer.
The Arc Lamp Ignitor is mounted under or next to the Arc Lamp. It provides the
high voltage pulse necessary to ignite the Xenon Arc Lamp that is the illumination
supply for the HJT Model 330, 340SC and 370SC projectors.
The System Power Supply’s Arc Lamp Supply section provides the necessary
voltage to activate the ignitor and to sustain the arc in the Arc Lamp once it has
been ignited. The SPS provides the power necessary to operate the ignitor.
The Ignitor is only active during the time between the Arc Lamp Power Supply
energizing and the Arc Lamp igniting. During steady state operation and when the
projector power is off, the ignitor is inactive.