Projector Service Manual
Table Of Contents
- DECLARATION OF CONFORMITY
- BZSAFE.PDF
- CH1INTRO.PDF
- CH2SYSDE.PDF
- Functional Descriptions
- Contents
- Cover and Base
- External Power Requirements
- Electronics Systems Overview
- System Power
- Card Cage
- Circuit Boards
- Raster Timing Generator Board (RTG) p/n 100568
- Sync Generator
- Sync Detector and Selector
- Serration and Equalization Lockout
- Phase Locked Loop
- VSYNC Detector, Field Separator, and Mux
- Adjustment Counters
- Serial Communication
- Raster Timing Generator I/O
- Interlocks and Protection
- Horizontal Deflection Board P/N 102523 (HDB)
- Vertical Oscillator
- Horizontal Phase Locked Loop
- Horizontal Centering
- Horizontal Power Supply
- Flyback Switching
- Geometric Correction
- Output Section
- Horizontal Sweep Failure Detection
- Serial Communication
- Horizontal Deflection Board I/O
- Interlocks and Protection
- Vertical Deflection Board P/N 102521(VDB)
- Vertical Preamps
- Vertical Amplifiers
- Sweep Failure Detection
- Side Pincushion and Keystone Correction
- Horizontal Linearity Correction
- Top and Bottom Pincushion and Keystone Correction
- Correction Amplifiers
- Serial Communication
- General I/O
- Interlocks and Shutdowns
- Video Processor Board P/N 104672 (VPB)
- Decoder
- Video/Sync Mux
- V & H Sync Strip
- SG Sync Strip
- B, G, and R Brightness and Contrast Amplifiers
- On-Screen Switch
- Gamma Correction
- Switch Logic and Video Enable
- RGB Sensitivity and Threshold Amplifier
- ILA® Bias
- Dynamic Focus Amplifier
- Serial Communication
- General I/O
- Interlocks and Protection
- Video Amplifier Board P/N 103567 or 103774 (VAB)
- Video Signal
- Failure Detection
- Beam Current Sense
- DC Restore
- Arc Protection
- Blanking
- Enable Circuit
- Focus
- Filament Supply
- General I/O
- System Controller Board P/N 104668 (SCB)
- General Functional Description
- CPU
- Working and Compressed Memory
- Expanded Memory
- Correction Address Generator
- DACs
- DSP
- Overlay Memory
- Overlay Address Generator
- Overlay Interface
- LED Display Buffers and Logic
- RS232 Interface
- IR Interface
- IIC Interface
- Serial Interface
- General I/O
- Backplane Board p/n 100571
- Optical Section
- Image Light Amplifier
- Functional Descriptions
- CH3ADJST.PDF
- CH4MAINT.PDF
- Maintenance Remove/Replace)
- Contents
- Introduction
- Projector Covers
- Ventilation Filters
- Arc Lamp Assembly
- System Power Supply
- Electronics Module
- Cathode Ray Tube (CRT)
- Video Amplifier Board (VAB)
- CRT Yoke
- High Voltage Power Supply (HVPS)
- Card Cage (Printed Circuit Boards)
- Image Light Amplifier Assembly
- Projection Lens
- (SCB) Socket Battery Replacement
- Recommended Spares
- Maintenance Remove/Replace)
- CH5TRBSH.PDF
- HGLOSS.PDF
Chapter 5---Troubleshooting
5-9 Model 330, 340SC, and 370SC Service Manual
Problem and
Symptom to
Check
Possible Solution Service
Manual
Operator
Manual
LEDs 200, 300, or
400 on the
vertical
deflection are
unlit.
Replace Vertical Deflection Board. 4.11
LEDs 200 and 201,
or 300 and 301,
or 400 and 401
on the vertical
deflection are
unlit.
Replace Horizontal Deflection
Board
if any two (2) are unlit.
4.11
Increasing G2
voltages
decreases
brightness level
for all CRTs.
Faulty High Voltage Power Supply
under full load. Replace High
Voltage power Supply.
4.10
Arc Lamp
Arc lamp will not
light-'clicking'
sound audible
when projector is
commanded ON.
Replace worn out Arc Lamp. 4.4
'Clicking' sound not
audible when
projector is
commanded ON.
System Power Supply or Ignitor
Assembly
faulty. Replace SPS or Ignitor
Assembly.
4.5
Arc Lamp ignites
but will not stay
lit.
Replace defective Ignitor
Assembly.
4.4
Brightness flicker or
Picture very
dim.
Arc Lamp may have too many
hours.
Replace Arc Lamp.
4.4