Installation Guide

2 of 2
One Lithonia Way, Conyers, GA 30012 • Phone: (800) 705-SERV (7378) • Visit us at www.acuitybrands.com
©2020 Acuity Brands Lighting, Inc Rev 09/20
Note: Before beginning the installation
A. Make sure all power is off, shutting power off in breaker box to areas where
downlights are to be installed is recommended.
B. Load the Samsung SmartThings
®
App to your Android or iOS mobile device.
Required Tools (not included): Safety glasses and gloves.
1. Double check and measure the ceiling hole. Make sure it is the correct size
for outside rim of the luminaire to cover the hole while still allowing the
back of luminaire to sink in to the ceiling and springs to hold firmly.
 Remove existing retrofit can if present or move it out of the way since it
will not be needed for installation.
 If new hole is to be cut, use provided hole template. Place template over
the desired location. Trace the outer ring with a pen or pencil (not
included). Cut the opening with a saw (not included).(Figure 1)
2. Open the cover of the remote driver box. Push and remove one of the
knockouts on the side plate.
 Locate power supply leads from remote driver box and connect to power source
using wago connectors (provided).
 Connect black wire to live wire, white wire to neutral wire, and green wire with
ground (as shown) and secure using connector. Close the cover of the box. (Figure 2)
3. Connect the remote driver box to the light fixture and tighten the nut
connector by hand. Arrow on the male and female parts of the connector between
the driver and fixture cable should match. (Figure 3)
4. Place remote driver box thru the cut-out hole.
 MUST follow local electric code for rigid attachment and
placement of the remote driver box. (Figure 4)
WARRANTY
Limited warranty located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Technical Services Phone (800) 705-SERV (7378)
Figure 1
Figure 3
THREAD
LOCK
Figure 2
 Verify that fixture is wired properly.
 Verify that fixture is grounded correctly.
 Verify that the line voltage at the fixture is correct.
If further assistance is required for installation issues, contact:
Technical Support at: (800) 705-SERV (7378).
For setup support using the Samsung SmartThings® App. contact
technical support at: [phone]
This LED module does not require service or new bulbs to change.
Optional Mounting Kits: Instruction sheet for new construction plate
and joist bar kit can be found at www.acuitybrands.com
WARNING:
 DO NOT PLACE YOUR HAND UNDERNEATH SPRING CLIP
DURING REMOVAL PROCESS. SNAPPING OF THE CLIPS CAN CAUSE
INJURIES TO THE HAND. (Figure 7)
 DO NOT USE ANY OTHER DRIVER EXCEPT THE JUNO
DRIVER THAT IS INCLUDED WITH THE FIXTURE.
 DO NOT CONNECT MULTIPLE MODULES TO ONE DRIVER.
 DO NOT OPEN THE MODULE AND SIDE PLATE OF THE
REMOTE DRIVER BOX - NO SERVICEABLE PARTS INSIDE.
Figure 6
Figure 7
DO NOT
PLACE YOUR
HAND
DO NOT
PLACE YOUR
HAND
Figure 5
PULL UP
THROUGH
CEILING
HOLE
Figure 4
ATTACH USING PROVIDED
KEYHOLE FITTINGS
(MOUNTING
OPTIONAL)
ROUND HEAD SCREWS
SIDE WALL
5. Pull the spring clip on the fixture up
and through the ceiling hole and place
module in the hole making sure the
spring clips are holding securely.
(Figure 5)
6. Turn the power back on. If the mod-
ule doesn’t illuminate within 5 seconds,
turn power off, carefully remove the
module and double check all wiring and
replace. (Figure 6)
7. Once the fixture is operational, activate the app on your mobile control
device, and follow the instructions listed in the QUICK START GUIDE.
Trouble Shooting Guide
If this fixture fails to operate properly, use the guide below to diagnose
and correct the problem.
ACCESS
NEUTRAL WIRE
(FROM POWER SUPPLY)
GROUND WIRE
(FROM POWER SUPPLY)
LIVE WIRE
(FROM POWER SUPPLY)
NEUTRAL WIRE
GROUND WIRE
LIVE WIRE
NEUTRAL
WIRE
(WHITE)
GROUND
WIRE
(BARE COPPER /
GREEN)
LIVE
WIRE
(BLACK)
(FROM POWER SUPPLY)
(FROM DRIVER BOX)
connector
connector
connector
INSTALLATION INSTRUCTIONS
JunoConnect
TM
(Bluetooth
®
/ Zigbee
®
)