Installation Guide

ENGINEERING DATA
ULH109 ULH214 ULH322 ULH430
Total input power (watts) 20 40 60 80
Total Operating AMPS .17 .34 .50 .70
Power Factor .99 .99 .99 .99
REV-4/10
PRODUCT SPECIFICATIONS
Lamp 20W-12-volt halogen bi-pin lamps supplied with fixture
• Projected 6,000 hour life based on actual operating voltage in
fixture.
Transformer Integral Electronic 120 to 12-volt step down
transformer is accessible for maintenance without having to
remove fixture.
Housing Extruded aluminum • Designer white, black, brushed
bronze or brushed silver finish.
Reflector Specular aluminum reflector behind each lamp.
Diffuser Clear prismatic tempered glass lens for maximum light
transmission • Reverse-angled to minimize preceived brightness
• Captive lens has hinged design for tool-less relamping • Spring-
loaded retention bar prevents lens from accidently being bumped
loose.
Switch Convenient integral Hi/Lo/Off rocker switch.
Dimming For best results use dimmer specifically designed for use
with electronic low voltage transformers.
Labels UL Listed.
DIMENSIONS
UNDERCABINET LIGHTING
PRO-SERIES HALOGEN
20W - 12-volt Halogen Lamps
ULH109, ULH214,
ULH322 and ULH430
I1.1.0
Project:
Fixture Type:
Location:
Contact/Phone:
PRODUCT DESCRIPTION
The Pro-Series Halogen modular series with integral electronic
transformer operates 12-volt halogen lamps to deliver the best color
rendering with maximum light output and lamp life. The efficient
operation of low voltage lamps, along with a unique
housing/reflector system, reduces mounting surface temperatures
well below what is typical for halogen undercabinet fixtures. Pro-
Series Halogen fixtures are optimized for fast permanent installation,
mounting either flush to the rear backsplash or to the front lip of
cabinetry to suit project conditions and homeowner preference.
INSTALLATION
ULH series fixtures optimized with a center rear wiring access
compartment and push-in 3-wire electrical connectors for quick
electrical connection without having to open the fixture or remove
the lens. Rear wiring access compartment covers provided with
push-in connector for non-metallic cable and knockout for feed thru
wiring capability. Multiple off-center knockouts provided in two,
three and four lamp fixtures. Die-cast fitting for 3/8” flexible metal
conduit supplied in a hardware pack. Fixtures may be mounted
flush to the backsplash or up against the front lip of the cabinetry
using captive external mounting screws.
Portable To install as a portable fixture, use the 3-wire grounded
cord & plug (ULH-CP sold separately).
Optional Direct Wire Optional direct wire module (ULH-DWM
sold separately) facilitates code-compliant installation of fixture at
front edge of cabinetry. Supplied with 36” field-shortenable
jumper cord to bring power to either end of the fixture.
Electrically Connecting Multiple Fixtures Up to 10 fixtures
may be electrically joined together using either the straight joiner
connector supplied with each fixture or the optional JC3 jumper
cords. See accessories table for lengths and finishes.
ACCESSORIES
Catalog No. Description
JC3-8-WH,-BL 8” Jumper Cord
JC3-17-WH,-BL 17” Jumper Cord
JC3-26-WH,-BL 26” Jumper Cord
ULH-CONN 3/8” Miniature Die-Cast Electrical Connector
ULH-CP-WH,-BL 3-Wire Grounded Cord & Plug
ULH-DWM-WH,-BL Direct Wire Module
PRODUCT CODES
Catalog Number Finish Overall Length Lamp
ULH109-BL Black 9
1
/
2
” 1-20W
ULH109-BZ Brushed Bronze 9
1
/
2
” 1-20W
ULH109-SL Brushed Silver 9
1
/
2
” 1-20W
ULH109-WH Designer White 9
1
/
2
” 1-20W
ULH214-BL Black 14” 2-20W
ULH214-BZ Brushed Bronze 14” 2-20W
ULH214-SL Brushed Silver 14” 2-20W
ULH214-WH Designer White 14” 2-20W
ULH322-BL Black 22” 3-20W
ULH322-BZ Brushed Bronze 22” 3-20W
ULH322-SL Brushed Silver 22” 3-20W
ULH322-WH Designer White 22” 3-20W
ULH430-BL Black 30” 4-20W
ULH430-BZ Brushed Bronze 30” 4-20W
ULH430-SL Brushed Silver 30” 4-20W
ULH430-WH Designer White 30” 4-20W
PRO-SERIES HALOGEN 5 MINUTE DIRECT -WIRE INSTALLATION
Step 1 Attach supply
wires to rear access cover.
Step 2 Connect supply
wires to fixture leads
using push-in connectors.
Step 3 Mount fixture to
cabinet bottom using
captive mounting screws.
Maximum cabinet bottom contact temperature: less than 60˚ C.
1"
4 1/2"