JKU 6436 GEBRAUCHSANWEISUNG OPERATING INSTRUCTION D t 2222679-15
t CONTENTS Instructions for the User Instructions for the Installer Important Safety Instructions 18 Technical specifications 24 Description of the Appliance 19 Installation 25 Use 20 Cleaning the interior Starting-up Temperatur control Fresh food refrigeration Freezing fresh food Storage of frozen food Thawing Ice-cube production Movable shelves Positioning the door shelves Hints Hints for refrigeration Hints for freezing Hints for storage of frozen food Maintenance Defrosting Periodic clean
IMPORTANT SAFETY INSTRUCTIONS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety.
■ ■ ■ ■ t During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the relevant paragraph. Attention: keep ventilation openings clear of obstruction. If the appliance is transported horizontally, it is possible that the oil contained in the compressor flows in the refrigerant circuit.
USE Cleaning the interior Freezing fresh food Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. The 4-star compartment ( ) is suitable for long term storage of commercially frozen food and for freezing fresh food.
t Movable shelves The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired. For better use of space, the front half-shelves can lie over the rear ones. D338 Positioning the door shelves To permit storage of food packages of various sizes, the central door shelf can be adjusted in height. To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required.
■ ■ it is advisable to show the freezing-in date on each individual pack to enable you to keep tab of the storage time; do not put carbonated liquids (fizzy drinks, etc.) in the freezing compartment as they may burst.
t The freezer compartment, however, will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thickness of the frost exceeds 4 mm. During this operation it is not necessary to switch off the power supply or to remove the foodstuffs. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: 1. pull out the plug from the wall socket or turn the thermostat knob to the «O» setting; 2.
Periods of non-operation When the appliance is not in use for long periods, take the following precautions: remove the plug from the wall socket; remove all food: defrost and clean the interior and all accessories; leave the door ajar to allow air to circulate to prevent unpleasant smells. Interior light The light bulb inside the refrigerator compartment can be reached as follows: 1. unscrew the light cover securing screws; 2. unhook the moving part by pressing it as shown in the figure.
t INSTALLATION lf this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lock unusable before you discard the old appliance. This will prevent it from becoming a death-trap for a child. Grid preparation Left door opening: Remove the left side (A) of the grid cutting it from the rear (see figure).
Door reversal 10 To reverse the opening direction of the door, proceed as shown in the figures: 13 4 1 9 12 5 11 3 3 2 Warning! If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. In that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier. 1 6 Inner door reversal 1. Using a screwdriver release bracket (1) by pressing on the internal spring (Fig.
t Building in the appliance under a worktop 60 0 1 5 min50 . 600 2 DO013 1. The dimensions of the recessed installation area must correspond with those indicated in the figure. 1xB 2xC 2 4. Push the appliance into place. The plug socket necessary for connection of the appliance to the electricity supply should be positioned, so that the plug is not placed in the recess. 1xA 12 2 1 2 1 2 596 1 2. Installation kit 5 55 x ma Li89 Left hand bracket + 5.
II52 6. If necessary, pads are supplied for the rear feet to make sliding the appliance in and out of the recess easier. To fit the pads, press them onto the rear feet. If required, the dimensions of these pads can be reduced by breaking them where marked. 5 8. Screw appliance into place and retain the cabinet with screws. 9. To mount the furniture door proceed as shown in the figures: 2 1 a 10 2 C 1 4 B 3 b 3 7.
t a b C clic C clic 1 2 45 ° c 8 3 UPPER PART OF KITCHEN FURNITURE PANEL 1 10 a = = 2 = 10 b 9 = LOWER PART OF KITCHEN FURNITURE PANEL 275 11 275 x ma 100 9/a 12 29
A 13 10. Refit the covering strip. Fitting the plinth Important For the efficient operation of the appliance, it is important that the original ventilation grid is used. ■ a = 100 b = 150 ■ For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments. The same applies to an opening height dimension B=870 mm and a plinth height dimension b=150 mm.
