JKI 2035 GEBRAUCHSANWEISUNG OPERATING INSTRUCTION D t 2222745-86
t CONTENTS Instructions for the user Instructions for the installer Important Safety Instructions 14 Technical specifications 18 Description of the appliance Use 15 16 Installation 18 Cleaning the interior Starting-up Temperatur control Fresh food refrigeration Inner arrangement Defrosting Maintenance Periodic cleaning Periodic of non-operation Interior light Customer service and spare parts Positioning Electrical connection Door reversibility Instructions for totally built-in appliances 16 1
IMPORTANT SAFETY INSTRUCTIONS It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is supplied with the appliance in order that the new owner can be acquainted with the functioning of the appliance and the relevant warnings. These warnings are provided in the interest of safety.
t Installation ■ ■ ■ ■ Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Important: if the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. During normal operation, the condenser and compressor at the back of the appliance heat up considerably. For safety reasons, minimum ventilation must be as shown in the relevant Figure.
USE Cleaning the interior Fresh food refrigeration Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. To obtain the best performance: do not store warm food or evaporating liquids in the refrigerator; do cover or wrap the food, particularly if it has a strong flavour.
t Positioning the door shelves To permit storage of food packages of various sizes, the door shelves can be adjusted in height. To make these adjustments proceed as follows: Gradually pull the shelf in the direction of the arrows until it comes free, then reposition as required. For more thorough cleaning, the top door shelf can be removed by pulling it in the direction of the arrows, then refitting it in position.
CUSTOMER SERVICE AND SPARE PARTS If your appliance is still not working properly after making the above checks, contact the nearest service centre. To obtain fast service, it is essential that when you apply for it you specify the model and serial number of your appliance which can be found on the guarantee certificate or on the rating plate located inside the appliance, on the bottom lefthand side.
t Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. Important The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed.
2. Apply joint the sealing strip as shown in figure. D132 3. Slide the appliance into the recess, pushing it against the wall on the handle side. A D022 4. Open the door and push the appliance against the side of the kitchen unit opposite to that of appliance hinges. Fasten the appliance with 4 screws provided in the kit included with the appliance. Snap vent grille (C) and hinge cover (D) into position.
t 5. Apply covers (B) on joint cover lugs and into hinge holes. B D013 6. Separate parts A, B, C, D as shown in the figure. B A C D PR266 50mm 7. Place guide (A) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. A 20m m PR166 8. Fix cover (C) on guide (A) until it clips into place.
9. Open the appliance door and the furniture door at 90°. Insert the small square (B) into guide (A). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the squares and drill holes with Ø 2 mm at 8 mm from the outer edge of the door. Place the small square on the guide again and fix it with the screws supplied. 8mm A PR167 B 10. Should the lining up of the furniture door be necessary, use the clearance of slots.
