Cut Sheet

1300 S. Wolf Road • Des Plaines, IL 60018 • Phone [phone] • Fax [phone] • Visit us at www.acuitybrands.com/juno-recessed
Printed in U.S.A. ©2017 Acuity Brands Lighting, Inc. Rev. 03/01/17
1 of 2
Project:
Fixture Type:
Location:
Contact/Phone:
4”LOW VOLTAGE UNIVERSAL
TC NEW CONSTRUCTION
HOUSING, ELECTRONIC
TRANSFORMER
50W MR16
TC44 (E1)
G3.2.7
DIMENSIONS
5 3/8"
13 1/2"
Will expand
to 25"
(Reduces to 8 1/8"
with breakaway
feature)
6 3/4"
9 1/8"
12 1/8"
4 1/2” CEILING CUTOUT
PRODUCT DESCRIPTION
TC New Construction Housing design for use in non-insulated
areas • If installed where insulation is present, the insulation must
be pulled back 3” from all sides of the TC housing.
PRODUCT SPECIFICATIONS
Lamp One 12V, 50W MR16 lamp.
Socket Ceramic bi-pin socket with aluminum heat shield.
Trims Trim selection shown on reverse.
Transformer 120V to 12V Class 2 electronic transformer
mounted to junction box • Hatch part no. RS12-60 provided.
Dimming May be dimmed using dimmers specifically designed
for low voltage electronic transformers; consult factory or dimmer
manufacturer for additional information.
Labels U.L. listed for through-branch wiring, damp locations and
IP • Product thermally protected against improper use of lamps
or insulation • Union made • UL Listed/CSA certified • Trim
No. 441, 4401, 4402 and 4481 are wet location approved for
covered ceiling applications.
Testing All reports are based on published industry procedures;
field performance may differ from laboratory performance.
Specifications subject to change without notice.
INSTALLATION
Real Nail 3 Bar Hangers Telescoping, Patented (US Patent
D552,969) Real Nail
®
3 system permits quick placement of housing
anywhere within 24” O.C. joists or suspended ceilings • Integral
T-bar notch and clip secures housing in suspended ceiling grid –
no accessory clips required • 24” expansion stop allows quick
placement of fixture in standard grid spacing • Bars scored in two
locations for fast, clean breaking, allowing housing installation
in tight applications • Bars captive to mounting frame • Edge-
mounted for extra strength • Captive bugle-headed ring shank
nail for quick one-step installation and easy removal with claw
hammer for fixture relocation • Quick-Loc slot (location identified
on the mounting frame) and oversized locking set screw lock
fixture in position • Bar hanger foot contoured to align to bottom
of construction joist • Alternate mounting holes included.
Junction Box Pre-wired junction box provided with (5)
1
⁄2” and
(1)
3
⁄4” knockouts, (4) Non-metallic sheathed cable connectors and
ground wire, U.L. listed/CSA certified for through-branch wiring,
maximum 8 No. 12 AWG 90˚ C branch circuit conductors (4 in,
4 out) • Junction box provided with removable access plates
• Knockouts equipped with pryout slots.
Mounting Frame 22-gauge die-formed galvanized steel
mounting frame • 9
1
⁄8” L x 6
3
⁄4” W, (excluding bar hangers)
• Rough-in section (junction box, mounting frame, housing and
bar hangers) fully assembled for ease of installation.
Housing TC housing, 22-gauge galvanized steel • Housing
is vertically adjustable to accommodate up to a 1
1
⁄4” ceiling
thickness.
PRODUCT CODES
Catalog Number Input Voltage Lamp Rating (max)
TC44 E1
4" Low Voltage New Construction Non-IC 120V 12V 50W MR16
Housing and trim can be ordered together or separate, but will always ship separately.