Installation Sheet

For Juno T, TU and V Series Trac
Read all of these installation instructions before installing the Trac
system. Save these instructions and refer to them when additions or
changes in the Trac configuration are made. Use only fixtures and
fittings intended for use with Juno T, TU or V series Trac.
POLARITY
All Trac components are mechanically and visually polarized to assure
proper connections.
NOTE:
1. Trac face has a polarity line indicating “p” positive side.
2. Trac connectors have arrow which must point to polarity line.
3. Fixture adapter has arrows which must point to the polarity line.
4. Make sure power is OFF before wiring.
One Circuit Installation Data
Electrical Feed at Outlet Box and Mechanical Installation
A. To Mount Trac:
1. Attach fixture strap to outlet box.
2. Insert feed connector into Trac and secure with set screw.
3. Attach Trac to ceiling with toggle bolts or screws (if T-bar ceiling uses
T-bar clips, order separately). Maximum distance between clips is 4’.
4. If the Trac is pendant mounted, maximum pendant spacing is 4’
(minimum two pendants per Trac section).
5. Lock feed connector to nipple with lock nut.
B. To Wire Trac:
1. Use No. 12 or 14 AWG solid wire, copper only.
2. Pull wire through outlet box, fixture strap and connector.
3. Fasten positive wire to screw terminal marked P.
4. Fasten white wire (neutral) to screw terminal marked N.
5. Replace connector cover, secure with screw.
C. See fixture instructions for fixture installation to Trac.
D. Rated 120V, 60HZ, 20A.
Two Circuit Installation Data
Electrical Feed at Outlet Box and Mechanical Installation
A. To Mount Trac:
1. Attach fixture strap to outlet box.
2. Insert feed connector into Trac and secure with set screw.
3. Attach Trac to ceiling with toggle bolts or screws (if T-bar ceiling uses
T-bar clips, order separately). Maximum distance between clips is 4’.
4. If the Trac is pendant mounted, maximum pendant spacing is 4’
(minimum two pendants per Trac section).
5. Lock feed connector to nipple with lock nut.
B. To Wire Trac:
1. Use No. 12 or 14 AWG solid wire, copper only.
2. Pull wire through outlet box, fixture strap and connector.
3. Fasten one positive wire to screw terminal marked P1.
4. Fasten second positive wire to screw terminal marked P2.
5. Fasten white wire (neutral) to screw terminal marked N.
6. Replace connector cover, secure with screw.
C. See fixture instructions for fixture installation to Trac.
D. Rated 120V/240V, 60HZ, single-phase, 3-wire, grounded neutral.
4 inch octagonal box, wires from
outlet box fit thru nipple
4 inch octagonal box, wires from
outlet box fit thru nipple
Positive wire
White wire (Neutral)
2 Positive wires
White wire (Neutral)
Nipple
Lock nut
Nipple
Lock nut
Fixture
Strap
Screw terminal
Fixture
Strap
Screw terminal
Dead end fitting
with set screw
Feed end fitting
with set screw
Cover for outlet box and
connector cover
Feed end fitting
with set screw
Cover for outlet box and
connector cover
One Circuit Trac
Two Circuit Trac
Aluminum Trac extrusion
Noryl insulator
Polarity Line
Copper conductors
(Set back 3/8” from end)
Two circuits, two switches
System Capacity 40 Amps
20 Amps each circuit
One circuit, two switches
System Capacity 20 Amps
Two Circuit Wiring Information
P
1
N
P
2
P
N
P
2
P
1
1 of 2
1300 S. Wolf Road • Des Plaines, IL 60018 • Phone [phone] • Visit us at www.acuitybrands.com/juno-trac
©2017 Acuity Brands Lighting, Inc. Rev 3/17 P773
Technical Services Phone [phone]
INSTALLATION INSTRUCTIONS