Installation Manual

WARRANTY
Juno Lighting Group warrants that its LED step light products are free from defects in material and workmanship for five years from date
of purchase. Juno Lighting Group’s obligation is expressly limited to repair or replacement, without charge, at Juno Lighting Group’s
factory after prior written return authorization has been granted. This warranty shall not apply to products which have been altered or
repaired outside of Juno Lighting Group’s factory. This warranty is in lieu of all other warranties, expressed or implied, and without
limiting the generality of the foregoing phrase, excludes any implied warranty of merchantability. Also, there are no warranties which
extend beyond the description of the product on the company’s literature setting forth terms of sale.
1300 South Wolf Road • Des Plaines, IL 60018
PHONE [phone] • FAX [phone] • www.junolightinggroup.com
INSTALLATION INSTRUCTIONS
JUNO TYPE WET LOCATION LED MINI STEP LIGHT - LMSW
© 2011 Juno Lighting LLC Rev 2/11 P2976 pg 2 of 2
VERTICAL ORIENTATION (Cont.)
Step 5. Mount the backplate assembly (E) to J-box
with two 6-32 x1” screws and o-rings (F) supplied.
The 1/8 x 1/8 notch (M) must be to the bottom. Once
the backplate has been fastened securely to the wall,
wipe off any excess sealant. Failure to follow this
direction could allow moisture to penetrate the wall
assembly.
Step 6. Check to make sure that the gasket and
silicone sealant is compressed against the finished wall
surface.
Step 7A. Hook the Faceplate (A) onto the Backplate
Assembly (E) by first sliding the Upper Catch (G) -
located at the top of Faceplate, over the Upper Tab (H)
of Backplate Assembly (E). Press the Faceplate
downward onto the Backplate until it is firmly seated on
the upper tab. The Weep Hole (I) located at the corner
of Faceplate must be at the bottom.
Step 7B. For Hood Only.
Firmly sit the Faceplate (A)
onto the Backplate (E). The Weep Hole (I) located at
the corner of Faceplate (A) must be at the bottom.
Push the Faceplate (A) toward the wall making sure
that both Set Screws #4-40 (B) clear top and bottom
tabs (H). Skip Step 8.
Step 8. Push the lower portion of the Faceplate (A)
toward the wall making sure the Set Screw (B) clears
the bottom tab.
Step 9. Tighten the set screw #4-40 (B) (2 Set
Screws for Hood) with the Allen wrench provided.
Step 10. Apply the waterproof silicone sealant
(GE RTV-162 or equivalent) to seal all openings
between the face plate and the finished wall. Make
sure that weep hole (I) remains open.
HORIZONTAL ORIENTATION
(Figures 3 & 4)
Step 1. Separate the Faceplate (A) from rest of the
assembly by loosening the Set Screw #4-40 (B)
(2 Set Screws for Hood) located on the short edge
of the Faceplate with the Allen wrench provided.
Step 2. Remove (4) screws with o-rings (J) and
separate backplate/gasket (E) from Light Engine
Assembly (K).
Step 3. Turn backplate/gasket (E) 90º.
Step 4. Reinstall backplate/gasket (E) to Light Engine
Assembly (K) with (4) screws with o-rings (J). The
Ground Screw (C) at the heatsink must still be
at the bottom of the fixture.
Step 5. Follow steps 2 to 10 under “Vertical
Orientation”, keeping the Set Screw (B) and Notch (M)
on the right so that the Weep Hole (I) is on the bottom.
FIGURE 3
FIGURE 4
E
H
F
B
J
J
K
C
K
E
J
J
F
B
A
(I) Weep Hole
at Bottom
Notch (M)
on the same side
as the Set Screw
D
(I) Weep Hole
at Bottom
G