Instructions Manual Bedienungsanleitung
Instructions Manual INDEX RECOMMENDATIONS AND SUGGESTIONS...................................................................................................................... 4 CHARACTERISTICS.............................................................................................................................................................. 5 INSTALLATION .................................................................................................................................................
Bedienungsanleitung INHALTSVERZEICHNIS EMPFEHLUNGEN UND HINWEISE....................................................................................................................................12 CHARAKTERISTIKEN .........................................................................................................................................................13 MONTAGE.....................................................................................................................................
RECOMMENDATIONS AND SUGGESTIONS INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. • The minimum safety distance between the cooker top and the extractor hood is 650 mm. • Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood. • For Class I appliances, check that the domestic power supply guarantees adequate earthing.
CHARACTERISTICS Dimensions Components Ref. 1 8 9 10a 10b 20 Q.ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Directional Air Outlet grille 1 Flange ø 150 mm 1 Flange ø 120 mm 1 Adapting ring ø 120-125 mm 1 Closing element Ref. 12a 12e 12f Q.ty 4 2 5 12e 8 9 10a 1 Installation Components Screws 3,5 x 16 Screws 2,9 x 12,7 Screws 2,9 x 9,5 Q.
INSTALLATION Drilling the Support surface and Fitting the Hood • The Hood can be fitted directly on the lower surface of the Wall Units (650 mm min. above the Cooker Top) using the snapon Side Supports. • Make an opening on the lower surface of the Wall Unit, as indicated. (fig.1) • Before carrying out the installation, the wooden transportation protections screwed on the visor and on the canopy body must be removed. (fig.
Connections DUCTING VERSION AIR EXHAUST SYSTEM When installing the hood in ducting version, a rigid or a flexible pipe with the diameter corresponding to the flange diameter is used in order to connect the hood to the air outlet piping. • Fix the pipe with an adequate quantity of clamps (not supplied). • Remove possible charcoal filters. pipe RECIRCULATION VERSION AIR OUTLET 12e • Cut a hole ø 125 mm in any shelf that may be positioned over the hood. • Insert the flange 10a on the hood body outlet.
USE FUNCTION OF THE PULL-OUT SLIDING SUCTION PANEL With the sliding panel kept closed is not possible to start up the motor of the hood, on the contrary is possible to engine and/or to switch off the lighting system. When the sliding panel is pulled out the button pad is enabled, so that all functions are active and any functions that were activated previously will be restored.
The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button. Touch Basic functions Indicator lights control Dual Function L T1 When briefly pressed it switches the lighting system on and off. When pressed the motor is stopped, regardless of the speed it is set to. T2 When pressed the motor is set to the first speed T3 By a brief pressing the motor is set to the second speed.
MAINTENANCE Grease filters CLEANING OF THE METAL CASSETTE FILTERS Alarm reset • Stop the motor. • Press the F -touch control for at least 4 seconds until the T1 -touch control flashes. Cleaning the filters • Filters can be washed in the dish machine. They need to be washed every 2 months or even more frequently in case of particularly intensive use of the hood. • Pull out the sliding suction panel. • Remove the filters one by one, after having disconnected the relative fastening elements.
Odour filter (Recirculation Version) This filter cannot be washed or regenerated, and must be replaced when the F touch control starts to flash, or at least once every 4 months. The alarm is only triggered when the motor is on. Enabling/Disabling the alarm signal • In Recirculation Version Hoods, the Filter saturation Alarm must be enabled at the time of installation or later. • Switch off the lights and the motor.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
