Datasheet

4
Product Options
OPTION OPTION DESCRIPTION APPLICABLE PRODUCTS
T1/E1 interface module 8-port T1 and E1 interface module with standard RJ48 interfaces. IETF
PWE3 RFCs for SAToP and CESoPSN are supported.
CTP2008, CTP2024, CTP2056,
CTP150 (4-port only)
Serial interface module 8-port serial interface module is provided. Per-port soware selectable
interfaces, data rates, clocking, etc. are available. Interface support for
EIA232, V.24, EIA530, EIA449, V.35, and X.21 is provided.
CTP2008, CTP2024, CTP2056,
CTP150 (4-port only)
Serial with T1/E1 interface
option
Provides additional soware configurable T1 and E1 interface option
on the serial interface module. Full and fractional T1/E1 support is
also available.
CTP2008, CTP2024, CTP2056
Serial with Multiservice
interface option
Provides additional soware configurable single channel 4-wire trunk-
only interface option, IRIG-B option or high-quality analog option on the
serial interface module.
CTP2008, CTP2024, CTP2056, CTP150
(4-port serial and 2-port MS support only)
4WE&M analog module 8-port 4WE&M front module and rear transition module support type
I, II and V signaling options. The interface is a standard RJ21 amphenol
connector. One voice compression module is required in the CTP Series.
CTP2024, CTP2056
2WFXS analog module 24-port 2WFXS front module and rear transition module support loop
start, ground start and PLAR modes. The interface is a standard RJ21
amphenol connector. One voice compression module is required in the
CTP Series.
CTP2024, CTP2056
2WFXO analog module 12-port 2WFXO front module and rear transition module support
loop start and ground start modes. The interface is a standard RJ21
amphenol connector. One voice compression module is required in the
CTP Series.
CTP2024, CTP2056
Voice compression
module
The CTP Series Voice Compression module supports compression on
T1 and E1 DS0s and all analog voice bundles. The module supports
PCM, 32k G.726, 16k G.726, 16k G.728, 8k G.729, and 2.4k MELP
compression algorithms. The voice compression module also supports
echo cancellation, silence suppression, fax and modem detection, and
companding conversion between T1 and E1.
CTP2024, CTP2056
CTP clock main and
spoke modules
The CTP Series clock main and spoke modules are required when the
8-port serial module and compression module are installed into one
CTP Series device.
CTP2024, CTP2056
Gigabit Ethernet and Fast
Ethernet fiber SC modules
Provides for two 1000BASE-FX or 100BASE-FX SC connectors for IP
connectivity on the network side.
CTP2008, CTP2024, CTP2056
Gigabit Ethernet SFP fiber
options
SFP options include 1000BASE-T, 1000BASE-SX and 1000BASE-LX. CTP2008, CTP2024, CTP2056
Y-cable A cable connects one DTE to two DCE CTP Series serial ports to provide
1:1 hardware redundancy. This is only supported on serial interfaces.
This option is not available on T1 or E1 interfaces.
CTP2008, CTP2024, CTP2056, CTP150
AC power Internal AC power supply is provided. CTP2008, CTP2024, CTP2056, CTP150
DC power Internal DC power supply is provided. CTP2008, CTP2024, CTP2056
Redundant power Provides for dual redundancy power supplies. CTP2024, CTP2056