E-series™ Routing Platforms E320 Module Guide Release 8.1.x Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 USA 408-745-2000 www.juniper.
E320 8.1.x Module Guide This guide provides an overview and description of the line modules (LMs), switch route processor (SRP) modules, switch fabric modules (SFMs), and input/output adapters (IOAs) available for the E320 router. NOTE: A release may support multiple versions of a module or IOA. For information, see Software Compatibility in JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules. Table 1 on page 3 lists the modules and IOAs supported by the router.
Table 1: E320 Modules and IOAs Module/IOA Type Module Label First JUNOSe Support Page ES2 4G LM 7.0.1 5 LM-10 Uplink ES2 10G UPLINK LM 7.2.0 7 LM-10 ES2 10G LM 8.0.0 9 SRP-100 SRP-100 7.0.1 11 SRP-320 SRP-320 7.3.0 13 SFM-100 SFM-100 7.0.1 15 SFM-320 SFM-320 7.3.0 16 GE-4 IOA ES2-S1 GE-4 IOA 7.0.1 18 GE-8 IOA ES2-S1 GE-8 IOA 7.2.0 22 10GE IOA ES2-S1 10GE IOA 7.0.1 26 ES2-S2 10GE PR IOA 7.2.0 29 ES2-S1 OC3-8 STM1 ATM IOA 7.0.1 33 ES2-S1 OC12-2 STM4 ATM IOA 7.
E320 8.1.x Module Guide Table 1: E320 Modules and IOAs (continued) Module/IOA Type Module Label First JUNOSe Support Page ES2-S1 OC12-2 STM4 POS IOA 7.0.1 37 ES2-S1 OC48 STM16 POS IOA 7.0.1 40 ES2-S1 REDUND IOA 7.0.1 42 ES2-S1 SERVICE IOA 7.0.1 43 SRP IOA 7.0.
LM-4 Line Module LM-4 Line Module Module label ES2 4G LM Number of ports ■ Not applicable Software release ■ First supported: 7.0.1 Description ■ 200 W ■ Acts as frame forwarding engines for the physical interfaces ■ Responsible for processing data traffic ■ Pairs with IOAs to process data from different types of network connections ■ Supports a line rate of 128–byte packets on IOAs ■ The 100–Gbps switch fabric allocates 3.
E320 8.1.x Module Guide Alarms, errors, and events 6 ■ LM-4 Line Module ■ See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules.
LM-10 Uplink Line Module LM-10 Uplink Line Module Module label ES2 10G UPLINK LM Number of ports ■ Not applicable Software release ■ First supported: 7.2.
E320 8.1.x Module Guide When lit, LED indicates: LEDs Alarms, errors, and events 8 ■ LM-10 Uplink Line Module ■ OK (green)—Self-test passed ■ FAIL (red)—Failure detected ■ ONLINE (green)—Online with no alarms or errors ■ REDUN (green)—Redundant card available ■ See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules.
LM-10 Line Module LM-10 Line Module Module label ES2 10G LM Number of ports ■ Not applicable Software release ■ First supported: 8.0.
E320 8.1.x Module Guide When lit, LED indicates: LEDs Alarms, errors, and events 10 ■ LM-10 Line Module ■ OK (green)—Self-test passed ■ FAIL (red)—Failure detected ■ ONLINE (green)—Online with no alarms or errors ■ REDUN (green)—Redundant card available ■ See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules.
SRP-100 Module SRP-100 Module Module label SRP-100 IOA label SRP IOA Number of IOA ports ■ Not applicable Software release ■ First supported: 7.0.
E320 8.1.x Module Guide Board-level LEDs: LEDs ■ OK (green)—Self-test passed ■ FAIL (red)—Failure detected ■ ONLINE (green)—Online with no alarms or errors ■ REDUN (green)—Module is the spare system controller, is up, and is ready to take the role of the online system controller. When LED is not lit, module is not acting as the spare system controller.
SRP-320 Module SRP-320 Module Module label SRP-320 IOA label SRP IOA Number of IOA ports ■ Not applicable Software release ■ First supported: 7.3.
E320 8.1.x Module Guide Board-level LEDs: LEDs ■ OK (green)—Self-test passed ■ FAIL (red)—Failure detected ■ ONLINE (green)—Online with no alarms or errors ■ REDUN (green)—Module is the spare system controller, is up, and is ready to take the role of the online system controller. When LED is not lit, module is not acting as the spare system controller.
SFM-100 Module SFM-100 Module Module label SFM-100 IOA label ■ Not applicable Number of IOA ports ■ Not applicable Software release ■ First supported: 7.0.
E320 8.1.x Module Guide SFM-320 Module Module label SFM-320 IOA label ■ Not applicable Number of IOA ports ■ Not applicable Software release ■ First supported: 7.3.0 Description ■ 95 W ■ Switch fabric module (320 Gbps) ■ Works with the SRP-320 module to create a switch fabric ■ The 320–Gbps fabric allocates 10 Gbps of overall bandwidth to each line module slot.
SFM-320 Module Alarms, errors, and events ■ See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules.
E320 8.1.x Module Guide GE-4 IOA IOA label ES2-S1 GE-4 IOA Number of IOA ports ■ 4 Software release ■ First supported: 7.0.1 Description ■ 30 W ■ Half-height module ■ See Slot Combinations on page 63 for more information on combining IOAs in a slot. ■ Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths. ■ Uses either optical or copper SFPs. ■ The optical transceivers are 1000Base-SX, 1000Base-LX, and 1000Base-ZX compliant.
GE-4 IOA Cables and connectors (multimode [SX] ) ■ Up to four LC-style fiber-optic connectors ■ Transmit power: ■ Cables and connectors (single-mode [LX]) min: –9.5 dBm ■ max: –4 dBm Receive input power: ■ min: –20 dBm ■ max: 0 dBm ■ See the following corresponding table (SX Fiber Optic Cabling) for cabling requirements. ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
E320 8.1.x Module Guide Cables and connectors (single-mode [ZX] ) ■ Up to four LC-style fiber-optic connectors ■ Transmit power: ■ ■ min: –2 dBm ■ max: 3 dBm Receive input power: ■ min: –22 dBm ■ max: –3 dBm ■ See the following corresponding table (ZX Fiber Optic Cabling) for cabling requirements. ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
GE-4 IOA Table 5: ZX Fiber Optic Cabling Fiber Type Nominal Wavelength (nm) Maximum Operating Range (kilometers) 10 microns 1550 70 (43.
E320 8.1.x Module Guide GE-8 IOA IOA label ES2–S1 GE-8 IOA Number of IOA ports ■ 8 Software release ■ First supported: 7.2.0 Description ■ 21 W ■ Gigabit Ethernet ■ Half-height module ■ See Slot Combinations on page 63 for more information on combining IOAs in a slot. ■ Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths ■ Uses either optical or copper SFPs.
GE-8 IOA Cables and connectors (multimode [SX]) ■ One LC full duplex connector ■ Transmit power: ■ Cables and connectors (single-mode [LX]) min: –9.5 dBm ■ max: –4 dBm Receive input power: ■ min: –20 dBm ■ max: 0 dBm ■ See the following corresponding table (SX Fiber Optic Cabling) for cabling requirements. ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
E320 8.1.x Module Guide Cables and connectors (single-mode [ZX]) ■ One LC full duplex connector ■ Transmit power: ■ ■ min: –2 dBm ■ max: 3dBm Receive input power: ■ min: –22 dBm ■ max: –3 dBm ■ See the following corresponding table (ZX Fiber Optic Cabling) for cabling requirements. ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
GE-8 IOA Table 8: LX40 Fiber Optic Cabling (continued) 9 microns 1310 40 (24.85 miles) Table 9: ZX Fiber Optic Cabling Fiber Type Nominal Wavelength (nm) Maximum Operating Range (kilometers) 10 microns 1550 70 (43.
E320 8.1.x Module Guide 10GE IOA IOA label ES2-S1 10GE IOA Number of IOA ports ■ 1 Software release ■ First supported: 7.0.1 Description ■ 40 W ■ Full-height module ■ Uses a range of 10-gigabit small form-factor pluggable (XFP) transceivers to support different modes and cable lengths. ■ Ethernet (IEEE 802.3ae) ■ 10Gb Base-SR/LR/ER ■ Port can operate in full duplex mode with an average data rate of 3.
10GE IOA Cables and connectors (single-mode [LR]) ■ One LC full duplex connector ■ Transmit power: ■ Cables and connectors (single-mode [ER]) min: –8.2 dBm ■ max: 0.5 dBm Receive input power: ■ min: –14.4 dBm ■ max: 0.5 dBm ■ See the following corresponding table (LR Fiber Optic Cabling) for cabling requirements. ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information. ■ One LC full duplex connector ■ Transmit power: ■ LEDs ■ ■ min: –4.7 dBm ■ max: 4.
E320 8.1.x Module Guide Table 10: SR Fiber Optic Cabling Fiber Type Minimal Modal Bandwidth at 850 nm (MHz*km) Maximum Operating Range (meters) 62.5 microns 160 26 (85.3 ft) 200 33 (108.27 ft) 400 66 (216.54 ft) 500 82 (269.03 ft) 2000 300 (984.25 ft) 50 microns Table 11: LR Fiber Optic Cabling Fiber Type Nominal Wavelength (nm) Maximum Operating Range (kilometers) 9 microns 1310 10 (6.
10GE PR IOA 10GE PR IOA IOA label ES2-S2 10GE PR IOA Number of IOA ports ■ 2 ■ 1 active, 1 redundant Software release ■ First supported: 7.2.0 Description ■ 40 W ■ Full-height module ■ Uses a range of 10-gigabit small form-factor pluggable (XFP) transceivers to support different modes and cable lengths.
E320 8.1.x Module Guide Cables and connectors (multimode [SR]) ■ One LC full duplex connector ■ Transmit power: ■ Cables and connectors (single-mode [LR]) ■ 10GE PR IOA max: –1.0 dBm Receive input power: ■ min: –9.9 dBm ■ max: –1.0 dBm See the following corresponding table (SR Fiber Optic Cabling) for cabling requirements. ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information. ■ One LC full duplex connector ■ Transmit power: ■ min: –8.2 dBm ■ max: 0.
10GE PR IOA LEDs Board-level LEDs: ■ OK (green)—IOA online and is functioning properly ■ FAIL (red)—Failure detected Port LEDs: ■ LK (green)—Ethernet link is up ■ ACT (green)—Blinks when Ethernet traffic is being received Port labels: Alarms, errors, and events ■ W—Working port ■ P—Protect port (LK blinks when active cable is attached even though it is not the active working port) ■ See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ether
E320 8.1.x Module Guide Table 13: SR Fiber Optic Cabling Fiber Type Minimal Modal Bandwidth at 850 nm (MHz*km) Maximum Operating Range (meters) 62.5 microns 160 26 (85.3 ft) 200 33 (108.27 ft) 400 66 (216.54 ft) 500 82 (269.03 ft) 2000 300 (984.25 ft) 50 microns Table 14: LR Fiber Optic Cabling Fiber Type Nominal Wavelength (nm) Maximum Operating Range (kilometers) 9 microns 1310 10 (6.
OC3/STM1-8 ATM IOA OC3/STM1-8 ATM IOA IOA label ES2-S1 OC3-8 STM1 ATM IOA Number of IOA ports ■ 8 Software release ■ First supported: 7.0.1 Description ■ 50 W ■ Half-height module ■ See Slot Combinations on page 63 for more information on combining IOAs in a slot. ■ Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths.
E320 8.1.x Module Guide Cables and connectors (single-mode intermediate [IR-1]) Cables and connectors (single-mode long reach [LR-1]) ■ Up to eight LC full duplex connectors ■ Transmit power: ■ min: –15 dBm ■ max: –8 dBm ■ Center wavelength: 1310 nm ■ Receive input power: ■ min: –34 dBm ■ max: –7 dBm ■ Rated for 15 km (9.3 miles) of 9-micron core cable ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
OC12/STM4-2 ATM IOA OC12/STM4-2 ATM IOA IOA label ES2-S1 OC12-2 STM4 ATM IOA Number of IOA ports ■ 2 Software release ■ First supported: 7.0.1 Description ■ 40 W ■ Half-height module ■ See Slot Combinations on page 63 for more information on combining IOAs in a slot. ■ Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths.
E320 8.1.x Module Guide Cables and connectors (single-mode intermediate [IR-1]) Cables and connectors (single-mode long reach [LR-1]) ■ Up to two LC full duplex connectors ■ Transmit power: ■ min: –15 dBm ■ max: –8 dBm ■ Center wavelength: 1310 nm ■ Receive input power: ■ min: –28 dBm ■ max: –7 dBm ■ Rated for 15 km (9.3 miles) of 9-micron core cable ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
OC12/STM4-2 POS IOA OC12/STM4-2 POS IOA IOA label ES2-S1 OC12-2 STM4 POS IOA Number of IOA ports ■ 2 Software release ■ First supported: 7.0.1 Description ■ 30 W ■ Half-height module ■ See Slot Combinations on page 63 for more information on combining IOAs in a slot. ■ Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths.
E320 8.1.x Module Guide Cables and connectors (single-mode short reach [SR]) Cables and connectors (single-mode intermediate [IR-1]) Cables and connectors (single-mode long reach [LR-1]) 38 ■ OC12/STM4-2 POS IOA ■ Up to two LC full duplex connectors ■ Transmit power: ■ min: –15 dBm ■ max: –8 dBm ■ Center wavelength: 1310 nm ■ Receive input power: ■ min: –28 dBm ■ max: –7 dBm ■ Rated for 2 km (1.
OC12/STM4-2 POS IOA LEDs Board-level LEDs: ■ OK (green)—Physical link is connected properly and is functioning properly ■ FAIL (red)—Failure detected Port LEDs: ■ Alarms, errors, and events ALM—Bi-color LED: ■ Yellow: Local loss of signal exists ■ Red: Remote loss of signal exists ■ OK (green)—SONET is up and port is functioning properly. If not lit, a problem exists.
E320 8.1.x Module Guide OC48/STM16 POS IOA IOA label ES2-S1 OC48 STM16 POS IOA Number of IOA ports ■ 1 Software release ■ First supported: 7.0.1 Description ■ 30 W ■ Half-height module ■ See Slot Combinations on page 63 for more information on combining IOAs in a slot.
OC48/STM16 POS IOA Cables and connectors (single-mode intermediate [IR-1]) Cables and connectors (single-mode long reach [LR-2]) LEDs ■ Up to one LC full duplex connector ■ Transmit power: ■ min: –5 dBm ■ max: 0 dBm ■ Center wavelength: 1266 through 1310 nm ■ Receive input power: ■ min: –18 dBm ■ max: –0 dBm ■ Rated for 15 km (9.3 miles) of 9-micron core cable ■ See E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
E320 8.1.x Module Guide Redundancy IOA IOA label ES2-S1 REDUND IOA Number of IOA ports ■ 0 Software release ■ First supported: 7.0.1 Description ■ 10 W ■ Full-height module ■ Provides redundancy for line modules ■ Inserted in slot 0 and 11 only ■ Provides switchover when a line module fails ■ Provides N+1 redundancy for line modules ■ When inserted in slot 0, provides redundancy for a failed line module in slots 1–5.
Service IOA Service IOA IOA label ES2-S1 SERVICE IOA Number of IOA ports ■ 0 Software release ■ First supported: 7.0.
E320 8.1.x Module Guide SRP IOA Module label SRP IOA IOA label ■ Not applicable Number of IOA ports ■ 3 Software release ■ First supported: 7.0.1 Description ■ 10 W ■ Pairs with SRP module ■ Interfaces with the SRP modules through the system's midplane. ■ Ethernet (IEEE 802.
Appendix A IOA Protocol Support This appendix lists the layer 2 and layer 3 protocols and applications that IOAs support in combination with the listed LM. IOAs are identified by their physical labels. See Table 1 on page 3 for a list of IOAs and their identifying labels. The designation “not yet fully qualified” that appears in some tables in this appendix indicates that support for the protocol or application on the specified IOA has not yet been fully qualified by Juniper Networks.
E320 8.1.
Appendix A: IOA Protocol Support Table 16: Ethernet IOAs with ES2 4G LM (continued) Protocol or Application ES2–S1 GE-4 IOA (with ES2 4G LM) ES2–S1 GE-8 IOA (with ES2 4G LM) ES2–S1 10GE IOA (with ES2 4G LM) LNS support—peer side Yes Yes Yes Local loopback No No No MDL (maintenance data link) No No No MPLS Yes Yes Yes Multilink Frame Relay No No No Multilink PPP No No No Network Address Translation (NAT) No No No NBMA (multipoint ATM) No No No OSPF Yes Yes Yes Packet
E320 8.1.
Appendix A: IOA Protocol Support Table 17: Ethernet IOAs with ES2 10G Uplink LM (continued) Protocol or Application ES2–S2 10GE PR IOA (with ES2 10G Uplink LM) IS-IS Yes J-Flow Statistics No L2TP/IPSec No LAC support—access side No LAC support—peer side Yes LNS support—peer side Yes Local loopback No MDL (maintenance data link) No MPLS Yes (LER only) Multilink Frame Relay No Multilink PPP No Network Address Translation (NAT) No NBMA (multipoint ATM) No OSPF Yes Packet Mirrorin
E320 8.1.
Appendix A: IOA Protocol Support Table 18: Ethernet IOAs with ES2 10G LM (continued) Protocol or Application ES2–S1 GE-8 IOA (with ES2 10G LM) ES2–S2 10GE PR IOA (with ES2 10G LM) IPv6 multicast Yes Yes IPv6 neighbor discovery Yes Yes IS-IS Yes Yes J-Flow Statistics No No L2TP/IPSec No No LAC support—access side Yes Yes LAC support—peer side Yes Yes LNS support—peer side Yes Yes Local loopback No No MDL (maintenance data link) No No MPLS Yes (LER only) Yes (LER only) Mu
E320 8.1.
Appendix A: IOA Protocol Support OCx/STMx ATM IOAs Table 19: OCx/STMx ATM IOA Protocol or Application ES2–S1 OC3–8 STM1 ATM IOA ES2–S1 OC12–2 STM4 ATM IOA Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels Yes Yes APS/MSP No No ATM Yes Yes BERT No No BGP Yes Yes BGP/MPLS VPNs Yes Yes Bridged Ethernet Yes Yes Bridged IP Yes Yes CBF No No Cisco HDLC No No DHCP external server Yes Yes DHCP local server Yes Yes DVMRP and GRE support—access side Yes Yes
E320 8.1.
Appendix A: IOA Protocol Support Table 19: OCx/STMx ATM IOA (continued) Protocol or Application ES2–S1 OC3–8 STM1 ATM IOA ES2–S1 OC12–2 STM4 ATM IOA VPLS (virtual core interfaces) Yes Yes VRRP No No OCx/STMx ATM IOAs ■ 55
E320 8.1.
Appendix A: IOA Protocol Support Table 20: OCx/STMx POS IOA (continued) Protocol or Application ES2–S1 OC48 STM16 POS IOA ES2–S1 OC12–2 STM4 POS IOA IPv6 multicast Yes Yes IPv6 neighbor discovery No No IS-IS Yes Yes J-Flow Statistics Yes Yes L2TP/IPSec No No LAC support—access side No No LAC support—peer side Yes Yes LNS support—peer side Yes Yes Local loopback No No MDL (maintenance data link) No No MPLS Yes Yes Multilink Frame Relay No No Multilink PPP No No Netw
E320 8.1.
Appendix A: IOA Protocol Support Service IOA Table 21: Service IOA Protocol or Application ES2–S1 SERVICE IOA Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels No APS/MSP No ATM No BERT No BGP Yes BGP/MPLS VPNs Yes Bridged Ethernet No Bridged IP No CBF No Cisco HDLC No DHCP external server No DHCP local server No DVMRP and GRE support—access side No DVMRP and GRE support—server side Yes (over dedicated tunnel server ports) Dynamic interfaces No F4 OAM and
E320 8.1.
Appendix A: IOA Protocol Support Table 21: Service IOA (continued) Protocol or Application ES2–S1 SERVICE IOA VRRP No Service IOA ■ 61
E320 8.1.
Appendix B Slot Combinations This appendix lists the IOA slot combinations and contains the following sections: ■ IOA Slot Combinations on page 63 IOA Slot Combinations Depending on the software release and IOA type, you must install IOAs in certain slots and bays combined with other IOAs in the same slot: ■ You must insert some IOAs only in the upper bay (Adapter 0) of each IOA module slot.
E320 8.1.
Appendix C Module Name Cross-Reference Information ■ Module Name Cross-Reference Information on page 65 Module Name Cross-Reference Information Use Table 23 on page 65 to find the label name, software display name, and model number of a module.
E320 8.1.
Appendix D Product Reclamation and Recycling Program ■ Product Reclamation and Recycling Program on page 67 Product Reclamation and Recycling Program Juniper Networks is committed to environmentally responsible behavior. As part of this commitment, we continually work to comply with environmental standards such as the European Union’s Waste Electrical and Electronic Equipment (WEEE) Directive and Restriction of Hazardous Substances (RoHS) Directive.
E320 8.1.x Module Guide Products returned through our reclamation process are recycled, recovered, or disposed of in a responsible manner. Our packaging is designed to be recycled and should be handled in accordance with your local recycling policies.
This product includes the Envoy SNMP Engine, developed by Epilogue Technology, an Integrated Systems Company. Copyright © 1986-1997, Epilogue Technology Corporation. All rights reserved. This program and its documentation were developed at private expense, and no part of them is in the public domain. This product includes memory allocation software developed by Mark Moraes, copyright © 1988, 1989, 1993, University of Toronto.
